11022442511 Kenmore Washer - Instructions

Remove the center cover with a screwdriver then loosen the 7/16 bolt with an impact driver socket ccw to remove completely biggest issue is removing bottom cover tried pick tools only thing that was succesful was some dawn dishsoap on the center bolt area to loosen enough to lift up the cover replace the hub part that had worn spline grooves remember to use blue loctite on the 7/16 bolt before re-installing cw to tighten bolt

Actually, I "Youtubed" it. I entered the info from the washer and found what was similar. What would help is when you tilt the washer (on back or front) so you can look at what you're going to work on to match (or closely match) what is on Youtube. It is SO easy, it's unbelievable.

I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.

Unplug washer
Take back panel off
Un plug lid switch
Take screwdriver snap out switch
Snap in New switch
Plug it in
Replace back panel plug in washer
Wash

Watch video on the site and the insulation will be easy and take about 30 min.

Removed two 1/4” screws from the backside of control panel. Plastic putty knife slide under front of control panel to release the clips and allowing panel removal. Shut water supply off and removed both hot/cold hoses from valves. Removed the two T-20 screws which allowed the removal of the existing leaking valve assembly. Installed in reverse and it worked perfectly!!

Research showed it was the transmission and the actuator . Parts were super easy to install and it solved the issue 100%

PS - I put some light lithium grease on the transmission and it’s quieter than it was when new

Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I already had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.

Went with the instructions

When to PartSelect Web site, used their trouble shooting guide, Used their advice, which was to replace the actuator. bought and installed the actuator which took around 20 minutes or so. washer started working fine after replacing. Thanks to the website I save a lot of money. Thanks PartSelect

Was the video and I started everything fell into place. Thank you very much

W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.

There are a lot of complaints, with these new energy efficient washers, no matter the brand, on the amount of water that is being used, and not properly washing your cloths, while in the wash cycle.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.

My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!

Removed old one (2 screws) slid in place and screwed in.