This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This agitator is for washers.
Agitator rotates back and forth to move the clothes inside the tub to clean the load.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work glove...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Helen
September 22, 2022
Just received agitator. Cap needed for agitator
For model number 11022442511
Hello Helen, thank you for your question. The Washer Fabric Softener Dispenser Cup is part PS11770292. Hope this helps, good luck with this repair.
Was this helpful?
Thank you for voting!
Claudio
May 23, 2023
When the wash cycle is started it fills with just a bit of water, then I hear a clicking/humming noise and it doesn't go to the next step which is agitate. Rinse/Spin - Drain/Spin - Clean Washer all work. The only problem is it doesn't "agitate". I would hate to guess at what part(s) I may need.
https://www.partselect.ca/PS12347261-Whirlpool-W11116569-CNTRL-ELEC.htm?SourceCode=20&SearchTerm=11022442511&ModelNum=11022442511&ModelID=7225741#Troubleshooting
For model number 11022442511
Hi Claudio, thank you for reaching out. Based on the description that you have provided, we would recommend checking the shift actuator, part number PS16221077. A washing machine shift actuator is the component that causes the transmission to change between agitation and spinning modes. If the shift actuator is defective, the transmission may be stuck in spin mode, resulting in the washer not agitating. If this part is faulty, you may need to replace it. We hope this helps!
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned it back up and got caught up on laundry. good day when the washer is fixed.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
