11021392012 Kenmore Washer - Instructions

All Instructions for the 11021392012
76 - 90 of 94

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The spin cycle was very noisy & shook the whole machine.
1 person found this instruction helpful.
  • Ace from VENICE, FL
  • Very Difficult
  • More than 2 hours
The part we needed wasn’t pictured — nor the quantity identified. There are 4 absorbers required for full replacement. I received one absorber — 3 1/2 inches X 1 1/2 inch wide X 1/8 inch thick. Including shipping, the cost was $53.00!! Outrageous! A 10 foot roll of the same thing can be bought online for less than $20.00.
... Read more >By the way, it didn’t solve the problem.

Paul
Was this helpful?
Thank you for voting!
Shakes and moves | Noisy
1 person found this instruction helpful.
  • Philip from BURIEN, WA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Followed video on your web site, and used that for ways to fix, good directions. If I was more organized it prob would of taken about an hour or less
Was this helpful?
Thank you for voting!
Washer drum banging on spin cycle
1 person found this instruction helpful.
  • David from KISSIMMEE, FL
  • Really Easy
  • 15 - 30 mins
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Was this helpful?
Thank you for voting!
Banging when in spin cycle.
1 person found this instruction helpful.
  • ROBERT from OXLY, MO
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this helpful?
Thank you for voting!
Extreme imbalance
1 person found this instruction helpful.
  • Jerry from OROVILLE, WA
  • Really Easy
  • 30 - 60 mins
  • Pliers
This washer would not go into spin cycle without going out of balance no matter how we arranged the contents in the drum. We were looking to buy a front loader when I happened open this company with video instructions and positive comments from other people with the same issue. For the cost it was worth a try. Following the video and in l ess than one hour the washer was back in service. It now operates like the day we installed it new. Highly recommend this fix which should save you hundreds on a new washer.
Was this helpful?
Thank you for voting!
Washer shaking and banging loudly during spin cycle
1 person found this instruction helpful.
  • Dan from KISSIMMEE, FL
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Replaced the suspension rods
Was this helpful?
Thank you for voting!
Springs worn out on the suspension rods. (Noisy drum in spin cycles)
1 person found this instruction helpful.
  • Douglas from BEECH ISLAND, SC
  • Easy
  • 30 - 60 mins
  • Nutdriver
The video posted on this site will walk you right through the repair. Great service. Thanks!
Was this helpful?
Thank you for voting!
The washer was shaking during the spin cycle
1 person found this instruction helpful.
  • Michele from ROCHESTER, NY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Exactly like the video from the website
Was this helpful?
Thank you for voting!
Washer would go into the cycle to rinse dry.
1 of 2 people found this instruction helpful.
  • Daniel from WARMINSTER, PA
  • Really Easy
  • 30 - 60 mins
  • Socket set
Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.
Was this helpful?
Thank you for voting!
Making groaning noise in spin
1 of 3 people found this instruction helpful.
  • Harold from Blaine, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driv en Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Was this helpful?
Thank you for voting!
door latch broke
0 of 1 people found this instruction helpful.
  • Diana from Chimacum, WA
  • Easy
  • 15 - 30 mins
  • Nutdriver
Figuring out how to take the lid off was the hard part. Took out the old and replaced with new and put lid back on and rehooked up.
Was this helpful?
Thank you for voting!
Replace drain hose
3 of 11 people found this instruction helpful.
  • Brian from DREXEL HILL, PA
  • Easy
  • 30 - 60 mins
  • Pliers
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people found this instruction helpful.
  • Howard from Boynton Beach, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol oring refer handles. Thank you
Was this helpful?
Thank you for voting!
The lid lock switch on our clothes washer went out
  • Steven from Keenesburg, CO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I had to remove 3 screws from the back of the washer to be able to lift the top. Then remove 3 screws under the lid which held the switch in, unplug the old part and put the new one in. It was quite sinple. The most difficult part was figuring out you have to slide the top of the washer forward a bit to be able to tilt it up.
Was this helpful?
Thank you for voting!
would not unlock
  • Michael from Lincoln, RI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Disassembled ,as assembled.
Was this helpful?
Thank you for voting!
All Instructions for the 11021392012
76 - 90 of 94