- Home
- 11021392011
- Instructions
11021392011 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Stripped screws on a hub drive replacement
3 of 3 people
found this instruction helpful.
-
Bruce from GLOBE, AZ
- Easy
- 15 - 30 mins
-
Screw drivers
Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I alre
... Read more
ady had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.
Read less
Was this helpful?
Thank you for voting!
Washer walking during spin cycle
3 of 3 people
found this instruction helpful.
-
Tricia from HARLEYSVILLE, PA
- Easy
- 30 - 60 mins
-
Socket set
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF ... Read more I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF ... Read more I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Read less
Was this helpful?
Thank you for voting!
Washer -Maytag Centennial- would NOT agitate. It would run through all cycles as indicated by the lights and even spin at the end, but never agitated. It also did not appeared to go into "sensing" mode at the start. Took a long time to move from "sensing" light to "wash" light. Did not hear or see a
3 of 3 people
found this instruction helpful.
-
Maxwell from RINGWOOD, NJ
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
There are a number of videos showing how to do this repair:
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ... Read more ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ... Read more ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
Read less
Was this helpful?
Thank you for voting!
Lid lock not working.
5 of 9 people
found this instruction helpful.
-
James from LIVONIA, LA
- Very Easy
- 15 - 30 mins
-
Socket set
Followed instructions.
Was this helpful?
Thank you for voting!
washer was draining but no spinning
3 of 3 people
found this instruction helpful.
-
JOSE from MILLBURY, MA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.
Then reverse the operation to stall the new part. Very easy.
Was this helpful?
Thank you for voting!
On Spin cycle washer jumping all over the place.
2 of 2 people
found this instruction helpful.
-
Tuan from LADSON, SC
- Really Easy
- 15 - 30 mins
-
Socket set
Just follow the video! Very easy.
Was this helpful?
Thank you for voting!
out of balance
2 of 2 people
found this instruction helpful.
-
Charles from ARVADA, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver
The info. was really helpful
Was this helpful?
Thank you for voting!
Belt needed to be replaced
2 of 2 people
found this instruction helpful.
-
Raymond from BRISTOL, CT
- Really Easy
- 30 - 60 mins
-
Socket set
Took the Cover off and installed belt.
Was this helpful?
Thank you for voting!
Washer would not adgitate
2 of 2 people
found this instruction helpful.
-
Joe from SAN JOSE, CA
- Very Easy
- Less than 15 mins
-
Nutdriver
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to
... Read more
them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Joe M. San Jose
Read less
Was this helpful?
Thank you for voting!
Washer wasn’t spinning fast enough to get the water out and it had a slight burning electrical smell.
2 of 2 people
found this instruction helpful.
-
craig from Oxford, CT
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
I simply followed your clutch drive repair video on YouTube, that wasn’t the problem so I replaced the motor… remove the cover that goes over the drive belt by taking out the two screws, remove the belt, unplug the wire connector going to the motor and remove the two bolts that hold it up and it falls right into your hand. Then reverse
... Read more
the process and that’s it. Very easy repair.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
My washer was always off balance.
2 of 2 people
found this instruction helpful.
-
Tracy from CONWAY, AR
- Really Easy
- 30 - 60 mins
-
Screw drivers
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this helpful?
Thank you for voting!
would not spin
2 of 2 people
found this instruction helpful.
-
John from INDIANAPOLIS, IN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
online videos were great. called to order and lady was very helpful. washer is now operating normal
Was this helpful?
Thank you for voting!
Remove and replace drain pump
2 of 2 people
found this instruction helpful.
-
Katherine from Saint Cloud, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people
found this instruction helpful.
-
James from PINE MOUNTAIN, GA
- Easy
- 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
Loud banging during spinning
3 of 5 people
found this instruction helpful.
-
Tom from LONG BEACH, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlp
... Read more
ool washers!
Read less
Was this helpful?
Thank you for voting!