11021102012 Kenmore Washer - Instructions

It was really easy. I popped off the agitation cone cover, used a socket set to remove the bolt which holds it all together. I removed the broken part, assembled the new one, using the old one as a example. I installed the new one. . . And I have clean clothes again. So much better to fix the old machine then buy a new one. . .

Removed the fabric softner despenser on to of agitator.
Removed the filter inside the agitator, pull straight up
Removed the bolt in the center of the agitator using a an extension on a 5/!6 socket.
Pulled the agitator out of washer removed inner works by hand. There are 4 fiberglass parts with teeth on them, I removed these 4 units and replaced them with new ones and it them put agitator back together in the reverse order. Works great.

The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.

Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....

Removed top agitator cover. Removed bolt and pulled out the cam holding the dogs. Assembled new cam w/dogs put in place and installed bolt plus agitator cap and was ready to wash.. Very Simple

1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!

This also gave me a chance to clean the agitator thoroughly!

Gently pry top of agitator off with small flat-blade screwdriver. Using the square end of a 1/2-inch socket extension, unscrew the plastic center "nut." Lift agitator off, remove center cone that holds the dogs, slip the retainer ring off, remove the worn dogs and replace. (Great opportunity clean the soap scum off the agitator!) Reverse the process to complete the repair.

first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.

I pulled the top off ( the fabric softner dispenser) unscrewed the nut pulled up on the agitator replaced the ears put it back together. . It works just as good as a $75.00 an hour repairman could have done. And the wife wanted a new washer? Ha

I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the repair man.

took the cover off the top of agitator, removed 3/8" bolt that went through cam and secured agitator. removed agitator and replaced the 4 agitator dogs and cam.
replaced agitator, tightened bolt, replaced cover. the washer works like new again? thankyou for your help and the correct parts.

Pulled cap off top of agitator, loosened bolt down in center of assembly and pulled collar up with pliers.
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.

Very simple; even a cave man could do it!

The repair was very easy, I took the top cap off the agitator and removed the recess bolt and pulled the agitator out of the washing machine,put the agitator on the floor and put my feet on the sides of the agitator and pulled the top haft apart,replaced the agitator directional cogs put back together work great

Remove the adgitator cap, remove a 7/16 bolt inside the agitator, lift out the top half the agitator and replace the guts with the new one. then insert and replace the bolt and snap the cap back on. The whole process didnt take 5 minnutes. it took longer to drive to the peoples house than it did to do the repair ! damn shame i couldnt charge by the minnute instead of by the hour. I cant believe kenmore got away with putting such junk on the market ! I' m sure many of these kits are being sold to those who do heavy loads od laundry!

I popped the liquid detergent cap off of the top of the Agitator. I then removed the seal cap to expose the Agitator dog assembly and bolt. I removed the entire Agitator dog assembly and Agitator by removing the single 7/16? bolt. I pulled the old dogs out, put the new dogs in and reassembled the Agitator Assembly.

Works like new!!