110200 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Spider coupling between motor and transmission broken
9 of 12 people
found this instruction helpful.
-
Robert from Friendswood, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy rep
... Read more
air.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
banging noise during spin cycle, tub out of balance
8 of 9 people
found this instruction helpful.
-
Russell from CHARLTON CITY, MA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer would'nt spin
9 of 12 people
found this instruction helpful.
-
Dean from Poplar Grove, IL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.
Was this helpful?
Thank you for voting!
washer is unbalanced during a spin cycle
7 of 7 people
found this instruction helpful.
-
Tiffany from NORTH OLMSTED, OH
- Really Easy
- Less than 15 mins
I watched a video on you tube before making the repair, there was only one bad rod support, location right rear, I recommend watching a video on you tube first, it is very simple to change, however the replacement of the part was not the solution to the unbalanced load during the spin cycle, so I guess I have some research to do.
Was this helpful?
Thank you for voting!
washer wasn't spinning after rinsing but the motor was running
8 of 10 people
found this instruction helpful.
-
Terry from HANCOCK, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Was this helpful?
Thank you for voting!
washer would not spin to extract vwater
7 of 7 people
found this instruction helpful.
-
Richard from WEEKI WACHEE, FL
- Very Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
will not go over step by step here as there are already a multitude of stories on site with exact situation as mine who have already done so.. What I will say is that PartSelect is easily the absolutely best site on the net for a complete problem diagnosis to finished repair experience. Just input your model # and describe the problem and
... Read more
you get instant diagnosis probabilities along with access to a long list of customer Q & A and reviews, along with step by step videos on diagnosing, dis- assembling, and re-assembling along with links to all parts needed and also some secondary tips along the way. The prices are fabulous (example: I got a clutch assembly kit with several parts and 2 additional parts as a just in case for $55 shpg incl, while my local appliance parts place wanted $59 plus tax for just the main part in my assembly kit with a no return policy and no part guarantee, plus it was only 1 day more to have PartSelect pkg arrive than I would have gotten part from local store). This site is FABULOUS !!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
I followed the video guide, which was excellent
7 of 7 people
found this instruction helpful.
-
Richard from NAPLES, FL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.
Machine works great now.
Machine works great now.
Was this helpful?
Thank you for voting!
Washer was stuck on rinse cycle
8 of 10 people
found this instruction helpful.
-
Michael from HARWICH PORT, MA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Research showed it was the transmission and the actuator . Parts were super easy to install and it solved the issue 100%
PS - I put some light lithium grease on the transmission and it’s quieter than it was when new
PS - I put some light lithium grease on the transmission and it’s quieter than it was when new
Other Parts Used:
Was this helpful?
Thank you for voting!
Shaking extreme
7 of 7 people
found this instruction helpful.
-
Barbara from RICHMOND, IN
- Really Easy
- 15 - 30 mins
-
Socket set
Per instruction sent with purchase
Was this helpful?
Thank you for voting!
No agitation, No spin, pump OK
7 of 7 people
found this instruction helpful.
-
Ernest from Midlothian, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold
... Read more
the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water Pump was leaking
9 of 13 people
found this instruction helpful.
-
Rick from Liberty, SC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people
found this instruction helpful.
-
Larry from Edgewood, TX
- Really Easy
- Less than 15 mins
-
Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
Making noise when spinning tub hit side of washer.
7 of 8 people
found this instruction helpful.
-
Ernestine from CARRIERE, MS
- Really Easy
- 30 - 60 mins
-
Socket set
Remove top of washer suspension
Rod goes on side of tub .
Rod goes on side of tub .
Was this helpful?
Thank you for voting!
washer wasn't spinning on final spin
7 of 8 people
found this instruction helpful.
-
Terry from HANCOCK, MD
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy
Was this helpful?
Thank you for voting!
When washer would go into spin cycle it would shake violently. This also prevented the spin cycle from completing leaving clothes soaked
7 of 8 people
found this instruction helpful.
-
Jonathan from NEW BRAUNFELS, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Followed videos sent with the repair items. It was very easy and solved my issue. My washer did not have the centering springs to begin with so I was unsure if I even needed them. But after replacing all the suspension rods and adding the pack of centering springs this has solved my issues
Other Parts Used:
Was this helpful?
Thank you for voting!