110200 Kenmore Washer - Instructions

All Instructions for the 110200
91 - 105 of 1385

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Darn thing hadn't "Agitated" for about 10 years!
11 of 13 people found this instruction helpful.
  • Stephen from Cornwall, NY
  • Easy
  • Less than 15 mins
  • Pliers
After removing the bolt (7/16" head), and using a pair of pliers to remove the 3-4 in deep "cup", it was immediately obvious how to assemble the new cup and pawls (ratchets).

Orienting the black "bearing" was not so obvious, but on closer inspection of the illustration, it became clear. The four "ears" of the bearing go clos est to the pawls. The little tabs that are co-planar to the ears fit into the four grooves of the new cup.

And here's the trick (besides making REALLY, REALLY SURE how the pawls orient)--Soak the black bearing piece in hot water to soften it up, and let it slide over the cup better. If you don't, you risk breaking it. If you do, it slides over and "clicjs" into place, with the ears resting right against the bottom lip of the cup, capturing the pawls.

Installation back into the washer is obvious.

The thing works like a charm! It hasn't worked this well for a decade!
Was this helpful?
Thank you for voting!
squeal and chirping while in risne / spin mode
10 of 10 people found this instruction helpful.
  • Thomas from GRAIN VALLEY, MO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this helpful?
Thank you for voting!
Washer was leaking.. determined it was center gasket
10 of 10 people found this instruction helpful.
  • Diane from BALTIMORE, MD
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.
Was this helpful?
Thank you for voting!
Top half of agitator wasn't moving
10 of 11 people found this instruction helpful.
  • Debra from Orange, CA
  • Really Easy
  • Less than 15 mins
  • Socket set
First, I wrestled off the top cap of the agitator. Then, I unscrewed the bolt and took out the cam. I noticed that the agitator dogs were worn smooth. I replaced them, put it all back together and VOILA! I bought the whole agitator kit, not knowing what I was going to find, because I wasn't a Magtag repair woman. It ended up that the cam that came in the kit was too big for my washer anyway. Luckily, all I needed was 4 plastic dogs. The price of the whole kit was so inexpensive anyway, it was no big deal. Especially because, I was looking to buy a new washer or a big repair bill. This website is great! Thank you.
Was this helpful?
Thank you for voting!
washing machine not draining
10 of 11 people found this instruction helpful.
  • michael from princeton, TX
  • Easy
  • 15 - 30 mins
  • Pliers
Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.
Was this helpful?
Thank you for voting!
tub oscillation
12 of 17 people found this instruction helpful.
  • leonard from phil campbell, AL
  • Really Easy
  • 15 - 30 mins
  • Pliers
placed washer on side and installed new pads
and returned washer upright
Was this helpful?
Thank you for voting!
Replaced ring that broke and washer that was bent on the edge.
22 of 47 people found this instruction helpful.
  • Kim from West Liberty, OH
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and starte d stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).
Was this helpful?
Thank you for voting!
Washer wouldn't start - Flashing Lid Light
13 of 20 people found this instruction helpful.
  • Marc from HOPE MILLS, NC
  • Easy
  • 30 - 60 mins
  • Screw drivers
I checked out the reviews and the recommendation of these "professionals", replaced the part easy enough when it came in. However, it didn't solve the problem. Got an actual professional to come in and see what the problem was, and they determined that gear oil was being leaked and it wasn't worth replacing.

Tried to get a re fund and return the part. Was told absolutely not. The money back guarantee is a lie.
Was this helpful?
Thank you for voting!
Hot water valve would barely open - take 35 mins to fill washer
10 of 11 people found this instruction helpful.
  • Kevin from ARLINGTON, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Pull the washer out from wall
Unplug the Washer
Close the supply line valves
Unscrew the supply lines, use bucket to catch line water
Remove 1 cover plate for elec lines (1 screw)
Remove 2 screws on edge of back plate for control panel
Slide long blade under front of control panel corners, pop the lock clips< br />Lay control panel forward - controls down
Compare new and old part - looks the same, wires, etc
Remove center screw on back plate cover to remove it
Unplug the elec wires connecting the valves and the control panel
Remove 2 screws holding the water valve outlet
swap out the old values for new valves
Reverse the process - step backwards and reassemble
Took me 36 minutes.
Tested the washer for Hot fill and later cold - both work
Was this helpful?
Thank you for voting!
spin cycle was not working / poor
11 of 14 people found this instruction helpful.
  • Craig from Plano, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive ass embly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.
Was this helpful?
Thank you for voting!
Tub banged against the front of case during spin
9 of 9 people found this instruction helpful.
  • Peter from Boca Raton, FL
  • A Bit Difficult
  • Less than 15 mins
  • Screw drivers
3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.
Was this helpful?
Thank you for voting!
Washer would not spin a full load.
11 of 15 people found this instruction helpful.
  • Ralph from Newbury Park, CA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people found this instruction helpful.
  • Larry from HICKORY, NC
  • Very Easy
  • Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Was this helpful?
Thank you for voting!
Tub off center. Upper agitator not driven.
10 of 13 people found this instruction helpful.
  • Thomas from Addison, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Socket set
Pop off the softener dispenser. Pull the cover/ seal out of the upper agitator. With 7/16" socket and extesion bar, remove bolt and pull upper agitator straight up and off. dump out old assembly and replace with new assembly. Set back in place and replace bolt. Repair kit comes with good instructions and new rubber O ring for bolt cover/ seal. (thanks).
The suspension spring takes more effort but not hard. with washer laying on face I used a piece of 2x4 to pick up the tub in the direction of the broken spring. Put the new spring through the wire hook loop and snake it through the slot in the frame and you can see how it locks in place. With the 2x4, push the tub toward the new spring until you can hook it through the slot on the tub frame. Done. Parts cost less than an estimate from a service call and I finished the job in 30 minutes, which includes unplugging the power cord, turning off the water and taking off the hoses so I could lay the washer down. Saved the website in my favorites for the same great prices and fast shipping next time.
Was this helpful?
Thank you for voting!
Washer tub off balance and noisy
9 of 10 people found this instruction helpful.
  • Gregory from Kent, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers
The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.

Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverag e with a 2 x 4 to take any residual tension off the springs.

Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors

Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.

If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Was this helpful?
Thank you for voting!
All Instructions for the 110200
91 - 105 of 1385