11018 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Excessive tub wobble, tubs leaning forward of normal
31 of 33 people
found this instruction helpful.
-
David from GLEN BURNIE, MD
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Washer is 29 years old. Found that tub spring hooks into a simple (non-reinforced) hole in the base frame, and it had worn the hole through through the edge of the frame (key hole style). Due to age and low cost of parts, ordered all suspension springs, brackets, & pads. Once they arrived, took the tubs out (first time for that), found
... Read more
that the suspension pads looked fine, but the wear pads showed a lot of wear and the front one was snapped in the middle, perhaps an after effect of the spring failure. From my lack of attention, initially tried to get front pad into the wrong set of holes, a bad fit; corrected. Simply drilled a near-by hole in the base frame for the tub spring.
While the tubs were out, took them outside and scrubbed them clean. Also cleaned agitator parts using bottle brushes. Followed the PartSelect videos and owner comments for procedures, methods. Found that some miss some important info, but if you watch others you can combine the info to find what you need re disassembly/assembly.
At one point while attempting to remove the outer tub, did not realize that the screw that holds the rear spring bracket to the tub also holds the tub to the suspension plate.
Took me most of a day for the whole process, and I ended up with pulled/spasmic muscles from all the bending over, mostly from cleaning parts I think. Very helpful to have the parts breakout drawings, videos, others' experience.
While the tubs were out, took them outside and scrubbed them clean. Also cleaned agitator parts using bottle brushes. Followed the PartSelect videos and owner comments for procedures, methods. Found that some miss some important info, but if you watch others you can combine the info to find what you need re disassembly/assembly.
At one point while attempting to remove the outer tub, did not realize that the screw that holds the rear spring bracket to the tub also holds the tub to the suspension plate.
Took me most of a day for the whole process, and I ended up with pulled/spasmic muscles from all the bending over, mostly from cleaning parts I think. Very helpful to have the parts breakout drawings, videos, others' experience.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer full of water, wouldn't cycle
34 of 43 people
found this instruction helpful.
-
peter from bethesda, MD
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Although your website mentioned removing 2 screws to open the control panel, it took a while to realize there were 2 screws and 2 hex nut screws to open it followed by 15 minutes of efforts to release the control panel from the top of the washer by sliding it forward. After that it took 2 minutes to replace the switch; the web comment of
... Read more
keeping the lid open was helpful.
Unfortunately, the lid switch was not the problem; replacing the timer did the trick, was very easy with the control panel already opened and required the purchase of 1/4 and 3/16 hex nut drivers.
Parts, shipping and tools cost $110 but the success of the repair with your parts and advice was priceless.
Unfortunately, the lid switch was not the problem; replacing the timer did the trick, was very easy with the control panel already opened and required the purchase of 1/4 and 3/16 hex nut drivers.
Parts, shipping and tools cost $110 but the success of the repair with your parts and advice was priceless.
Read less
Was this helpful?
Thank you for voting!
unbalanced load...knocking sound.
32 of 37 people
found this instruction helpful.
-
Edward from Easthampton, MA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, sc
... Read more
rew). Reassembled washer then ran wash for a cycle. Successful fix.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Found cracked brake shoe
33 of 41 people
found this instruction helpful.
-
Michael from Trafalgar, IN
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, the
... Read more
n used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.
Read less
Was this helpful?
Thank you for voting!
push to start switch was not working
33 of 43 people
found this instruction helpful.
-
Grace from New Smyrna Beach, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Removed the old one and installed the new one! What impressed me the most was the amount of time for delivery, one day! Actually it came before 24 hrs!!! Very impressive! I would highly recommend this company!!!
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people
found this instruction helpful.
-
Bill from Houston, TX
- Really Easy
- Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
Top door catch assembly had broken
29 of 31 people
found this instruction helpful.
-
tony from prineville, OR
- Easy
- Less than 15 mins
-
Screw drivers
It was so easy, that my wife did it the day we got the part before I got home from work. She wedged it out with a flat head screw driver and then pushed the new door catch assembly in with her thumb. Pretty simple, thanks for having parts like this available to the public!
Was this helpful?
Thank you for voting!
Washer would fill/empty but would not agitate nor spin
30 of 35 people
found this instruction helpful.
-
Ted from SOUTH MILWAUKEE, WI
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.
Pried off two clips attaching pump on motor using a flathead screwdriver. The r ... Read more ear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.
Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.
Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.
Replaced clips to hold motor on transmission and reinstalled screws holding clips.
IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!
Attach pump onto motor and replace clips. Double check everything is back in place.
Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.
First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.
Pried off two clips attaching pump on motor using a flathead screwdriver. The r ... Read more ear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.
Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.
Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.
Replaced clips to hold motor on transmission and reinstalled screws holding clips.
IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!
Attach pump onto motor and replace clips. Double check everything is back in place.
Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.
First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.
Read less
Was this helpful?
Thank you for voting!
Washer machine wouldn't start
30 of 35 people
found this instruction helpful.
-
Pedro from Riviera Beach, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws holding the main controller located on the back. I then slide forward the hole controller and I pulled out. Disconnected switch located on your left. (remember to place down washing machine lid before installing the new switch.)
Was this helpful?
Thank you for voting!
water would not stop filling and would overflow flooding floor
36 of 54 people
found this instruction helpful.
-
Patricia from Rose, OK
- Really Easy
- Less than 15 mins
replace part, which we received within one and half days and it works great. very satisfied
Was this helpful?
Thank you for voting!
Agitator loose spinning
27 of 28 people
found this instruction helpful.
-
Matthew from AUSTIN, TX
- Easy
- 30 - 60 mins
-
Socket set
Three of the four agitator cogs had broken. The agitator was able to spin freely both clockwise encounter clockwise which it should not be doing. I replaced the cogs as well as a couple additional parts just to be sure but the cogs were the important one. Very easy.
Other Parts Used:
Was this helpful?
Thank you for voting!
Severe water leak
27 of 29 people
found this instruction helpful.
-
Noel from Pollock, ID
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamp ... Read more s.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamp ... Read more s.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]
Read less
Was this helpful?
Thank you for voting!
washer moving 3 ft during the spin cycle sounding like elephants running through the house
29 of 37 people
found this instruction helpful.
-
Annie from Haines, OR
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Removed back panel to remove tub from shell. Unscrewed the brackets holding the springs. Used screw driver to pop out pads with hammer onto screw driver. Cleaned out tub and put grease on springs where they attach to bracket. Replaced panel and ran machine to find a leak. Took machine apart again to find the knocking of the tub again
... Read more
st the back panel caused a whole in the plastic tub. Silicon and mechanical tape. Washer works fine for now.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Agitator directional cogs worn out
26 of 30 people
found this instruction helpful.
-
Do n from LAWTON, OK
- Really Easy
- 15 - 30 mins
-
Socket set
Removed bolt holding top of agitator, removed top of agitator. Replaced parts. Reinstalled agitator. An old machine now works like a new model.
Other Parts Used:
Was this helpful?
Thank you for voting!
Two leaking hoses in my washing machine
29 of 39 people
found this instruction helpful.
-
Marc from Morton Grove, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Put the machine on its side. Remove old hoses and screw new ones into place. Done in under 20 minutes.
Other Parts Used:
Was this helpful?
Thank you for voting!