1100 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven burner would not come on.
20 of 20 people
found this instruction helpful.
-
Theodore C. from Winsted, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I am a retired lp Gas service person so this was quite
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.
Was this helpful?
Thank you for voting!
valves allowed water to overflow during the rinse cycle, sometimes took forever to fill.
22 of 26 people
found this instruction helpful.
-
Sam from Robertsville, MO
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I removed the screws holding the control unit down, removed a couple at the rear,
Disconnected the electrical clip that plugs into the top, under the control unit.
This allows enough slack to pivot it ( the control unit) upside down and get it out of the way enough to remove the spring clips that hold the top to the back.
... Read more >Popped out the two clips that hold the back to the top.
Pulled the back out, up until the plastic soap dispenser , (which is attached to the back) hits under the lip of the top.
This does not allow enough room to get to the valves.
I finally figured out you have to lift the entire top up high enough to clear the back while pulling it ( the back) out.
Disconnected the hose clamp, electric connectors, installed the new valves into the supplied mounting plate replaced the valves .
Re -connected the hose and electric connectors and re assembled the back.
The only problem I had was when one of the spring retainers that hold the back to the top popped off and fell inside the unit, which forced me to remove everything including the back bottom screws, which caused the sides to pop off, the mounting ears , which are attached to the back,
Took some finesse but finally retrieved the spring clamp and finished everything back together.
It was a bit tricky keeping the plastic gaskets between the back and the sides from falling inside as I reassembled it.
But all is well, and would have been more difficult without the expierence written by others who posted, on the site.
Thank you to all, for the help.
I hope my efforts will help someone else.
Disconnected the electrical clip that plugs into the top, under the control unit.
This allows enough slack to pivot it ( the control unit) upside down and get it out of the way enough to remove the spring clips that hold the top to the back.
... Read more >Popped out the two clips that hold the back to the top.
Pulled the back out, up until the plastic soap dispenser , (which is attached to the back) hits under the lip of the top.
This does not allow enough room to get to the valves.
I finally figured out you have to lift the entire top up high enough to clear the back while pulling it ( the back) out.
Disconnected the hose clamp, electric connectors, installed the new valves into the supplied mounting plate replaced the valves .
Re -connected the hose and electric connectors and re assembled the back.
The only problem I had was when one of the spring retainers that hold the back to the top popped off and fell inside the unit, which forced me to remove everything including the back bottom screws, which caused the sides to pop off, the mounting ears , which are attached to the back,
Took some finesse but finally retrieved the spring clamp and finished everything back together.
It was a bit tricky keeping the plastic gaskets between the back and the sides from falling inside as I reassembled it.
But all is well, and would have been more difficult without the expierence written by others who posted, on the site.
Thank you to all, for the help.
I hope my efforts will help someone else.
Read less
Was this helpful?
Thank you for voting!
The Dryer Would Not Turn On
19 of 19 people
found this instruction helpful.
-
Ribhe from Wildwood, MO
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about t
... Read more
wo days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.
Read less
Was this helpful?
Thank you for voting!
Although the motor was running, washer wouldn't agitate or spin.
20 of 24 people
found this instruction helpful.
-
Thomas from Commack, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench set
After disconnecting the electrical supply, first remove the two screws at either end of the control panel and fold it back away from the washer top. Then, unplug the electrical lid switch connection. Now, remove the two clips at either end on top to disconnect the housing from the washer back and chassis. The motor is sandwiched betwee
... Read more
n the water pump in the front and transmission at the rear. The Direct Drive Coupling connects the rear motor shaft to the transmisson. After you have taken the outter portion of the washer off, remove the two snap clips that hold the water pump in place and slide the pump off the front shaft. Best to also disconnect the upper hose connection so the pump can be moved out of the way. Caution though, remaining water in tub will drain out. Now remove the two screws that hold the clips in place which secure the motor to the transmission. Careful, as the old Direct Drive Coupling is probably destroyed, the clips are the only thing holding the motor in place and the motor needs to be supported so it won't drop to floor when the clips are removed. Be careful not to lose the four rubber grommets which sit between the motor and transmission bracket. After motor is on floor remove the old plastic slip-on direct drive coupling discs from both the motor and transmission shafts. The new replacement discs have steel centers which do not slide onto the shafts as easily as the old plastic ones did. I had to tap the center steel portion onto the shafts using a hammer and a deep wall socket the same width as the steel portion of the disc. Be careful! I'm sure that tapping the plastic portion of the disc to properly seat it on the shaft will break it away from the steel portion. In my case, It took me several attempts to completely seat the new discs. I had to do quite a bit of tapping to get the discs seated far enough onto the shafts so that the motor slipped easily against the transmission bracket grommets and the retainer clips snapped back into place easily. Reassembly is simply reversing the steps you took when taking the unit apart. Before putting the outter housing back in place, I checked to make sure everything was running smoothly by jumping out the electrical snap-in connection for the lid switch and running the machine in the spin cycle. Remember, if you don't jump out the lid switch and just try to test the unit in the aggitate cycle, the machine has to first fill with water.
Read less
Was this helpful?
Thank you for voting!
Dryer drum would not stop spinning when door was opened
26 of 43 people
found this instruction helpful.
-
Debra from Clarksburg, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
This dryer is a stackable washer/dryer. I removed all the buttons on the front panel along with the panel. I then was able to lift the front of the door and reach in to the door switch and plug. I unscrewed the old part, installed the new one. I then put the front panel and face plate back into position and screwed them back to the dryer
... Read more
casing. Lastly I put the knobs back on. I was extremely impressed at how easy it was to order and how quick the part came to my house. I am very satisfied with the service and the price and will use this site again in the future.
Read less
Was this helpful?
Thank you for voting!
Drum was binding because of worn bearing supporting front of dryer drum
23 of 35 people
found this instruction helpful.
-
Leslie from Townsend, GA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to gl
... Read more
ue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!
Read less
Was this helpful?
Thank you for voting!
Temperature setting not working
19 of 23 people
found this instruction helpful.
-
Robert from Buffalo, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!
NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use ... Read more the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.
NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use ... Read more the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.
Read less
Was this helpful?
Thank you for voting!
oven comes on to temp but will not reheat to a new temp third time trouble with same range
17 of 18 people
found this instruction helpful.
-
william from newport, VT
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was
... Read more
on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you
will sure use you again if the need arises thank you
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't lite
20 of 27 people
found this instruction helpful.
-
E Blake from Dauphin Island, AL
- Easy
- 15 - 30 mins
-
Screw drivers
Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the b
... Read more
ack of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.
Read less
Was this helpful?
Thank you for voting!
Top Half of Agitator would not function without appying sideways pressure
18 of 21 people
found this instruction helpful.
-
Donald from Fredericksburg, VA
- Really Easy
- 15 - 30 mins
-
Socket set
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remo
... Read more
ve black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...
Read less
Was this helpful?
Thank you for voting!
Agitator was barely agitating. Making a clicking noise.
17 of 18 people
found this instruction helpful.
-
Charmaine from Slidell, LA
- Easy
- 15 - 30 mins
-
Socket set
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Was this helpful?
Thank you for voting!
Would not spin
24 of 40 people
found this instruction helpful.
-
floyd from Slidell, LA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Was this helpful?
Thank you for voting!
The washer did not spin fast enough during the rinse cycle to adequately dry the load of clothes
17 of 19 people
found this instruction helpful.
-
Richard from EL SEGUNDO, CA
- A Bit Difficult
- More than 2 hours
-
Socket set
I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE
... Read more
DO THE STEP AND REPEAT
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
pilot lit but oven would light
19 of 26 people
found this instruction helpful.
-
Paul from Arlington, MA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
replaced the oven safety valve. This device uses heat from the pilot to hold open a valve that allows gas from the thermostat control to feed the main burner. It works by boiling the liquid mercury in the sensor bulb, producing the pressure to hold open the valve. My sensor had failed from old age, leaking the mercury.
Spill ... Read more ed mercury needed to be collected and properly disposed, and the valve was a tough fit among the sheet metal parts that form the path for the gas to the burner slots. The valve is secured by flat head sheet metal screws and the gas plumbing is a tapered pipe fitting. The sensor bulb has a small steel spring to hold it in the proper spot to sense the pilot light.
I used gas-rated pipe dope on the gas fitting, probably unnecessarily. Valve faces only 1/2 psi pressure...
Spill ... Read more ed mercury needed to be collected and properly disposed, and the valve was a tough fit among the sheet metal parts that form the path for the gas to the burner slots. The valve is secured by flat head sheet metal screws and the gas plumbing is a tapered pipe fitting. The sensor bulb has a small steel spring to hold it in the proper spot to sense the pilot light.
I used gas-rated pipe dope on the gas fitting, probably unnecessarily. Valve faces only 1/2 psi pressure...
Read less
Was this helpful?
Thank you for voting!
The movers broke both water intakes off flush with the back of the machine
16 of 17 people
found this instruction helpful.
-
Dennis from Oak Island, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.
Was this helpful?
Thank you for voting!