- Home
- 1069430012
- Instructions
1069430012 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bearings were going out
5 of 7 people
found this instruction helpful.
-
Doug from North Logan, UT
- Easy
- Less than 15 mins
-
Screw drivers
The refrigerator would make loud sounds humming sounds periodically. The bearings were going out on the evaporator motor. Emptied the freezer side of fridge. Unplugged unit. Took shroud off (6 screws). Removed the three wire clips. Pulled fan off shaft. Carefully pushed plastic strap to remove motor. Replaced with new motor. Carefully a
... Read more
ttached strap to hold motor. This seems very fragile so be very carefull to attach properly and not break. Reverse the rest and done in less than 15 minutes. 30 minutes cleaning the fridge.
Read less
Was this helpful?
Thank you for voting!
3 inches of frost in Fridge, 72 degrees in Fridgerator
6 of 10 people
found this instruction helpful.
-
Gerald from Orangeburg, SC
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First defrosted it to makes sure all Air flow was opened. Tested the Defroster heater with omh meter, it was OK. Found the location of the defrost timer on the online diagrams. Used nut driver to remove cover.
Replaced timer. The hardest part was decieding how to wire it up, tis was a universal kit and depending on how it was wired ... Read more as to how often the defrost ran. The firt choice was every 8 hours. Since this was going to be opened often, I picked that one.
Plugged it with in 24 hrs freezer wall mesured -5 and the fridge was at 30, so had to warm it up a bit.
Now all complaints gone, Ice making has been doing better also.
Replaced timer. The hardest part was decieding how to wire it up, tis was a universal kit and depending on how it was wired ... Read more as to how often the defrost ran. The firt choice was every 8 hours. Since this was going to be opened often, I picked that one.
Plugged it with in 24 hrs freezer wall mesured -5 and the fridge was at 30, so had to warm it up a bit.
Now all complaints gone, Ice making has been doing better also.
Read less
Was this helpful?
Thank you for voting!
fridge stopped cooling then the freezer
4 of 4 people
found this instruction helpful.
-
Joseph from DELTONA, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and
... Read more
it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,
Read less
Was this helpful?
Thank you for voting!
Erratic refrigerator temperature. Generally too cold - frozen produce.
4 of 4 people
found this instruction helpful.
-
Dave from BRIDGEWATER, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
The repair video was a great help in this specific repair and matched my refrigerator model exactly. The only issue was an apparent design change in the thermostat that I received. The location of the electrical leads has changed. It might be worth mentioning this in the video. Polarity is not an issue in this case, but if it was, it wou
... Read more
ld be worth noting in the video. So far the refrigerator has been operating normally.
Read less
Was this helpful?
Thank you for voting!
Not cooling properly and had to tap the thermostat to get it to kick on.
4 of 4 people
found this instruction helpful.
-
dee from FERNANDINA, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
My fridge was not cooling properly as I would have to tap the thermostat at times to get it to kick on again. Ordered the temperature control thermostat from this site t and watched video on how to install. Not hard at all and did it in under an hour. Fridge is working like new..
Was this helpful?
Thank you for voting!
Removed the old parts then connected the new parts.
4 of 4 people
found this instruction helpful.
-
Jonathan from OLIVE BRANCH, MS
- Really Easy
- 30 - 60 mins
-
Screw drivers
The compressor immediately started when I plugged the refrigerator back in. Around 24 hours later the freezer compartment was at 0 degrees, and the refrigerator was at 35 degrees.
Was this helpful?
Thank you for voting!
botrailer with frig without a icemaker
4 of 5 people
found this instruction helpful.
-
rich from racine, WI
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Wrench (Adjustable)
got the icemaker kit and started to add it to the frig found problems with the adaption to the frig in back for water filler tube but was able to make it fit. had to make a connection outside to water line with copper pipe added to hose with claps and saddle valve, turned it on and had leaks due to the schedule copper was the thin wall ty
... Read more
pe, got thicker type and installed it, no leaks, started making ice. it was nice to get the right kit to make things work out. thanks
Read less
Was this helpful?
Thank you for voting!
Lights not working some times
4 of 5 people
found this instruction helpful.
-
Harry from COLUMBIA STA, OH
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed old switch and installed new - but did not solve problem
Was this helpful?
Thank you for voting!
Refrigerator light would not turn on.
5 of 8 people
found this instruction helpful.
-
Suzanne from STERLING HTS, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom.
... Read more
The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Read less
Was this helpful?
Thank you for voting!
shelf support stud broke in half
4 of 5 people
found this instruction helpful.
-
Cindy from Fort Worth, TX
- A Bit Difficult
- 15 - 30 mins
-
Pliers
Removing old stud was difficult. It will not stap or pull out. Had to cut it off with a Dremel tool, then drill into the center of the old stud and pull out the pieces with needle nose pliers. Be careful, there are 2 metal pins on the side of the hole in the wall of the frid that need to stay there. These are in addition to the 2 met
... Read more
al pins on the shelf support stud. New stud popped right in easily.
Read less
Was this helpful?
Thank you for voting!
Frig wasn't reliable,kept going off and staying off until I discovered "hitting the knob" trick.
4 of 5 people
found this instruction helpful.
-
Bob from Norman, OK
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
I followed the procedures that others described that had the same problem,very handy
Was this helpful?
Thank you for voting!
Part went bad the freezer was freezing up and refrigerator not getting cold
3 of 3 people
found this instruction helpful.
-
Jessica from WILLIAMSBURG, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.
Was this helpful?
Thank you for voting!
Replaced broken shelf supports
4 of 6 people
found this instruction helpful.
-
Cheryl from Los Angeles, CA
- Really Easy
- Less than 15 mins
Took out old pieces and popped new ones in, just like that!
Was this helpful?
Thank you for voting!
Top half of freezer & fridge were not cooling. Freezer fan had been making unusually loud noises.
3 of 3 people
found this instruction helpful.
-
rich from PEMBROKE PNES, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver
Piece of cake. It took me longer to remove the food from the freezer, remove shelves and back panel than to do the repair. I heard the fan making some noises so I replaced both the fan and defrost thermostat. I used the instructions submitted by a another customer. My 20+ year old fridge is like new now.
Was this helpful?
Thank you for voting!
Freezer work perfectly, Refrigerator Stopped getting cold, water line froze, there was ice Forming around the condenser in the bottom of the refrigerator behind the drawers
3 of 3 people
found this instruction helpful.
-
Richard from STATEN ISLAND, NY
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. ... Read more I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. ... Read more I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
Read less
Was this helpful?
Thank you for voting!