1068682 Kenmore Refrigerator - Instructions

All Instructions for the 1068682
121 - 135 of 247

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light switch broke off
1 of 2 people found this instruction helpful.
  • Kathy from TEMECULA, CA
  • Very Easy
  • Less than 15 mins
  • Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
Broken shelf supports
1 of 2 people found this instruction helpful.
  • Bob from Las Vegas, NV
  • Really Easy
  • Less than 15 mins
Took just a few moments to install. The parts fit like a glove,
Was this helpful?
Thank you for voting!
Nonr
1 of 2 people found this instruction helpful.
  • Gaynell P from Spring, TX
  • Really Easy
  • Less than 15 mins
Replaced missing stud.
Was this helpful?
Thank you for voting!
Both front wheels were severly damaged needing replacement.
1 of 2 people found this instruction helpful.
  • James from Leesburg, VA
  • Easy
  • 15 - 30 mins
  • Socket set, Wrench (Adjustable)
I tipped the refrigerator back and my friend used an adjustable wrench to attach put the new wheel assembies on. I also used a socket wrench to get the old attacheement bolts to thread. I rolled the cleaned appliance in place and adjusted the wheels with the socket set for easy door closing. It went smoothly.
Was this helpful?
Thank you for voting!
Motor noise while running and clicking when shutting off
1 of 2 people found this instruction helpful.
  • Curtis from Sedona, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.
Was this helpful?
Thank you for voting!
fan motor had gone bad
1 of 2 people found this instruction helpful.
  • william from whitwell, TN
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.
Was this helpful?
Thank you for voting!
freezer and food section too warm
1 of 2 people found this instruction helpful.
  • William from Milford, MA
  • Easy
  • 30 - 60 mins
  • Socket set
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this helpful?
Thank you for voting!
Condenser Fan Failure
2 of 5 people found this instruction helpful.
  • Al from Tonka Bay, MN
  • Easy
  • 30 - 60 mins
  • Socket set
Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great !
Was this helpful?
Thank you for voting!
cooling fan quit
1 of 2 people found this instruction helpful.
  • George from Belhaven, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver
Ordered new fan motor on line took out old motor and replaced with new one
Was this helpful?
Thank you for voting!
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
2 of 6 people found this instruction helpful.
  • James from Howell, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this helpful?
Thank you for voting!
Refrigerator would not stay cold
2 of 6 people found this instruction helpful.
  • Jeremy from State College, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench set
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Repl aced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Was this helpful?
Thank you for voting!
Old tube had cracked due to being frozen....
1 of 3 people found this instruction helpful.
  • Stephen from Greensboro, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I followed the simple steps outlines in the great video! Thanks
Was this helpful?
Thank you for voting!
Every time we opened the fridge everything in the door shelf would fall out
1 of 3 people found this instruction helpful.
  • Jeremy from New Berlin, WI
  • Really Easy
  • Less than 15 mins
This website saved my marriage. For the past two years, every time we would open the fridge everything in the door shelves would fall all over the floor. This was not only embarassing when we would have family and friends over but I really got tired of my wife yelling every time she would open up the fridge. I tried every type of glue and repairs to try and fix it, finally gave up and thought the only way I would find peace at home was to purchase a new fridge. I accidently stumbled across your website and before I knew it and about $6 later my life improved more than you can imagine. The best part was how easy it was to find the part I needed with the detailed pictures you have. The part was shipped fast and very easy to install. I will definately use partselect again. Thanks!
Was this helpful?
Thank you for voting!
you have to turn it off and on to run.
0 of 1 people found this instruction helpful.
  • chris from woodland hills, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
Was this helpful?
Thank you for voting!
rocker switch broke off
0 of 1 people found this instruction helpful.
  • STANLEY from OAKLAND, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.
Was this helpful?
Thank you for voting!
All Instructions for the 1068682
121 - 135 of 247