1068682 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replacing evaporator fan
2 of 3 people
found this instruction helpful.
-
Steve from SAN CARLOS, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
My fridge did not have icemaker add on. The evap fan is in the freezer behind the back panel. Empty the freezer section (into a cooler) and turn the fridge off. Remove all the shelves in freezer section. Remove the shelf support tabs by lifting them up. use phillips head screwdiver to remove back panel in freezer section. Use nut driver t
... Read more
o remove fan shroud. Remove old fan and save the mounting arms. Install mounting arms on new fan and install fan. Install shroud, back panel, shelf mounts and shelves. Thats it!
Read less
Was this helpful?
Thank you for voting!
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
3 of 6 people
found this instruction helpful.
-
John from Greensboro, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right
... Read more
direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
Read less
Was this helpful?
Thank you for voting!
freezer would not freeze
1 person
found this instruction helpful.
-
Michael from HELENDALE, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thic
... Read more
k. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Read less
Was this helpful?
Thank you for voting!
Condenser fan motor froze up
2 of 4 people
found this instruction helpful.
-
Douglas from Mesa, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
Was this helpful?
Thank you for voting!
compressor not running
1 person
found this instruction helpful.
-
Doug from Lancaster, CA
- Really Easy
- 15 - 30 mins
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this helpful?
Thank you for voting!
door hinge broke.
2 of 4 people
found this instruction helpful.
-
Bernard from DONALDSONVLLE, LA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed door and replaced bushing bracket was ok.
Was this helpful?
Thank you for voting!
Condenser fan making noise
2 of 4 people
found this instruction helpful.
-
Richard from North Easton, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Wrench set
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easi
... Read more
er to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
Read less
Was this helpful?
Thank you for voting!
Shelf studs broke several years ago and I had a problem locating them. Finally wised up and checked Part Direct and found them, ordered the kit w/ 12 pieces. Then quickly watched the installation video. Took less than 30 minutes to replace two different studs. Wife is very happy.
1 person
found this instruction helpful.
-
Karl from BIRDSBORO, PA
- Easy
- 15 - 30 mins
-
Pliers
Simply took broken pieces of old stud out and replaced with the new ones. Used pliers to adjust them. Replace a freezer stud and a fridge stud.
Was this helpful?
Thank you for voting!
original motor stopped
2 of 4 people
found this instruction helpful.
-
Paul from Lowell, MI
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Socket set
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this helpful?
Thank you for voting!
freezer and refrigerator compartments not cold enough
1 person
found this instruction helpful.
-
Michael from Colorado Springs, CO
- Really Easy
- Less than 15 mins
-
Nutdriver
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people
found this instruction helpful.
-
Carolee from Spokane Valley, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
freezer quit working
1 person
found this instruction helpful.
-
Anthony from CIRCLEVILLE, OH
- Really Easy
- Less than 15 mins
-
Pliers
replaced relay switch
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some
Was this helpful?
Thank you for voting!
Broken kickplate retainers
1 person
found this instruction helpful.
-
Joe from STRATFORD, OK
- Very Easy
- Less than 15 mins
-
Screw drivers
replaced retainers. remove and replace four(4) phillips screws.
Was this helpful?
Thank you for voting!
No cold
1 person
found this instruction helpful.
-
Jacqueline from LEXINGTON PK, MD
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
Like you video
Was this helpful?
Thank you for voting!
The Light Socket Burned Out.
5 of 13 people
found this instruction helpful.
-
MATTHEW from STOCKTON, CA
- Really Easy
- Less than 15 mins
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this helpful?
Thank you for voting!