1068668421 Kenmore Refrigerator - Instructions

All Instructions for the 1068668421
76 - 90 of 163

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
compressor not running
1 person found this instruction helpful.
  • Doug from Lancaster, CA
  • Really Easy
  • 15 - 30 mins
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people found this instruction helpful.
  • Carolee from Spokane Valley, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
The Light Socket Burned Out.
5 of 13 people found this instruction helpful.
  • MATTHEW from STOCKTON, CA
  • Really Easy
  • Less than 15 mins
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this helpful?
Thank you for voting!
My wife broke the shelf support
1 person found this instruction helpful.
  • Hamid from Owasso, OK
  • Really Easy
  • Less than 15 mins
The new shelf support part fit perfectly. I needed no tools just slid it on the existing bracket. Super easy.
Was this helpful?
Thank you for voting!
A couple supports broke
2 of 4 people found this instruction helpful.
  • Michael from Cary, IL
  • Really Easy
  • Less than 15 mins
I simply slid off the broken supports, and slid the new ones on.
Was this helpful?
Thank you for voting!
freezer would not freeze
1 person found this instruction helpful.
  • Michael from HELENDALE, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thic k. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Was this helpful?
Thank you for voting!
Old door gasket became hard, and corners had rubber breaking apart some leakage of cold air
1 person found this instruction helpful.
  • lee from PORTLAND, OR
  • Easy
  • 30 - 60 mins
  • Socket set
Each side of the door had a metal strip bracket that was held in place by 1/4" sheet metal screws apprx. 8in. apart.. the outer lip of the gasket was tightened into these brackets..loosening the screws allowed the removal of the gasket from all 4 sides and corners..It was just the process of fitting the new gasket into the brackets that t ook the most time..making sure the new gasket was fitted all the way in for aligned proper fit,then tightening the screws evenly around the door frame..Then, 2 weeks later, this 27-year-old refrigerator's lower compressor went out,,and the refrigerator was history! YEAH!!
Was this helpful?
Thank you for voting!
Water tubing was accidentally broken from the back of the freezer.
1 of 2 people found this instruction helpful.
  • Lois from Thomasville, AL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together
Was this helpful?
Thank you for voting!
Poor design leaves fitting vulnerable to damage. Part was broken when pushed to close to the wall.
1 of 2 people found this instruction helpful.
  • Mike from Camas, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Simply removed the old and replaced with the new part.
Was this helpful?
Thank you for voting!
Two of the parts were broken so the shelf was laying on the drawers so neither could be used effectivly
1 of 2 people found this instruction helpful.
  • ROD from LINCOLN, NE
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Pulled out the stud with a wire cutter and replaced it with the exact part you shipped in the kit.

The other 2 parts just slipped on the brackets

Nice thing is now I have extra parts for the other shelf.
Was this helpful?
Thank you for voting!
Movers broke the icemaker water fill tube shoving my refrigerator through the front door.
1 of 2 people found this instruction helpful.
  • Christopher from Valley Village, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.

Then I put the new tube in, screwed the screws back in and reconnected the waterline.
Was this helpful?
Thank you for voting!
Nonr
1 of 2 people found this instruction helpful.
  • Gaynell P from Spring, TX
  • Really Easy
  • Less than 15 mins
Replaced missing stud.
Was this helpful?
Thank you for voting!
Broken shelf supports
1 of 2 people found this instruction helpful.
  • Bob from Las Vegas, NV
  • Really Easy
  • Less than 15 mins
Took just a few moments to install. The parts fit like a glove,
Was this helpful?
Thank you for voting!
Rocker on switch broke off
1 of 2 people found this instruction helpful.
  • David Barnes from ROSWELL, NM
  • Very Easy
  • Less than 15 mins
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this helpful?
Thank you for voting!
Light switch broke off
1 of 2 people found this instruction helpful.
  • Kathy from TEMECULA, CA
  • Very Easy
  • Less than 15 mins
  • Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
All Instructions for the 1068668421
76 - 90 of 163