1068668421 Kenmore Refrigerator - Instructions

All Instructions for the 1068668421
61 - 75 of 163

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken plastic part at top of water fill tube to freezer
2 of 2 people found this instruction helpful.
  • Jay from Mt. Pleasant, WI
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Simple. 1st, removed broken part to understand part (water fill tube to freezer, plastic part at top of fill tube cracked). 2nd go on your web site and look at prints to find part number, Study video to understand video. 3rd. Called customer service and lady was very nice and efficient. Placed order and received. Study video again a nd installed. My 9 year old grandson was visiting from out of town and assisted in installation. Just over 30 minutes to install
Was this helpful?
Thank you for voting!
Mounting bracket was riveted on old motor, mounting bracket holes on new motor were different
2 of 2 people found this instruction helpful.
  • MIKE from ARLINGTON, OR
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
removed shims on screws holding motor together, enlarged hole in mounting bracket so motor screws could also go through mounting brackets.
Was this helpful?
Thank you for voting!
freezer (later fridge too) wouldn't stay cold~
2 of 3 people found this instruction helpful.
  • David from MARYLAND HTS, MO
  • Very Easy
  • 30 - 60 mins
  • Nutdriver
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and acce ss panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Was this helpful?
Thank you for voting!
replacing evaporator fan
2 of 3 people found this instruction helpful.
  • Steve from SAN CARLOS, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
My fridge did not have icemaker add on. The evap fan is in the freezer behind the back panel. Empty the freezer section (into a cooler) and turn the fridge off. Remove all the shelves in freezer section. Remove the shelf support tabs by lifting them up. use phillips head screwdiver to remove back panel in freezer section. Use nut driver t o remove fan shroud. Remove old fan and save the mounting arms. Install mounting arms on new fan and install fan. Install shroud, back panel, shelf mounts and shelves. Thats it!
Was this helpful?
Thank you for voting!
Shelves in freezer falling off
2 of 3 people found this instruction helpful.
  • wendy from palm coast, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people found this instruction helpful.
  • Gail from Golden, CO
  • Really Easy
  • Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
The plastic water fill tube got cracked when we moved. I called a parts company and they told me they couldn't just sell me the tube I would have to buy a whole kit for about $50 dollars. I decided to glue the tube. It worked for a while then it started leaking. So I thought I would have to buy
3 of 6 people found this instruction helpful.
  • Joseph from Chesterfield, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.

Thanks so much! You saved me a bundle!!
Was this helpful?
Thank you for voting!
Connection leaked as tube entered freezer
1 person found this instruction helpful.
  • Robert from MERRIMACK, NH
  • Very Easy
  • 15 - 30 mins
Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.
Was this helpful?
Thank you for voting!
door hinge broke.
2 of 4 people found this instruction helpful.
  • Bernard from DONALDSONVLLE, LA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed door and replaced bushing bracket was ok.
Was this helpful?
Thank you for voting!
Shelf studs broke several years ago and I had a problem locating them. Finally wised up and checked Part Direct and found them, ordered the kit w/ 12 pieces. Then quickly watched the installation video. Took less than 30 minutes to replace two different studs. Wife is very happy.
1 person found this instruction helpful.
  • Karl from BIRDSBORO, PA
  • Easy
  • 15 - 30 mins
  • Pliers
Simply took broken pieces of old stud out and replaced with the new ones. Used pliers to adjust them. Replace a freezer stud and a fridge stud.
Was this helpful?
Thank you for voting!
freezer and refrigerator compartments not cold enough
1 person found this instruction helpful.
  • Michael from Colorado Springs, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this helpful?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 people found this instruction helpful.
  • Cathy from HOPATCONG, NJ
  • Very Easy
  • Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
Freezer occasionally had a temperature alarm.Clicking noise also.
1 person found this instruction helpful.
  • Barry from FORD CITY, PA
  • Really Easy
  • Less than 15 mins
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this helpful?
Thank you for voting!
No cold
1 person found this instruction helpful.
  • Jacqueline from LEXINGTON PK, MD
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Like you video
Was this helpful?
Thank you for voting!
Plugged it in.
1 person found this instruction helpful.
  • Adam from GLOVERSVILLE, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this helpful?
Thank you for voting!
All Instructions for the 1068668421
61 - 75 of 163