1068648621 Kenmore Refrigerator - Instructions

All Instructions for the 1068648621
121 - 135 of 176

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Switch was not working after a repairman had fixed something else
0 of 4 people found this instruction helpful.
  • Jackie from Nova, OH
  • Really Easy
  • Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this helpful?
Thank you for voting!
noisey fan
0 of 4 people found this instruction helpful.
  • Richard from Morgan, UT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
yup
Was this helpful?
Thank you for voting!
Both light bulbs had been replaced, but lights did not turn on.
  • Richard from Arlington, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this helpful?
Thank you for voting!
The freezer compartment was not cold enough.
  • Tom from Paducah, KY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I found the condenser fan was not working so I bought a new condenser fan kit and installed it. Fixed!
Was this helpful?
Thank you for voting!
Frozen Lettuce In Crisper
  • Mary E. from Chicago, IL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!
Was this helpful?
Thank you for voting!
Condenser motor stopped working
  • Chris from Greenville, OH
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Removed bad motor with socket set and pliers then removed the connectors from the old motor and soldered them on the new one. Then installed new motor. Works like new! Problem Solved! Easy fix!
Was this helpful?
Thank you for voting!
condenser fan wore out
  • Nancy from Gallatin, TN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.
Was this helpful?
Thank you for voting!
Switch didn't work
  • Don from Laramie, WY
  • Easy
  • 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
excessive water in condensate pan
  • michael from woodstock, MD
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
just as video instructions said, very easy just following them ,part arrived in very short time and was exact fit completely satisfied, saved repair man service charges and wait time
Was this helpful?
Thank you for voting!
Intermitant squealing noise from freezer area.
  • Harry from Torrance, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I basically followed the step-by-step instructions at the parts order website. I removed the shelves and rear panels to access the fan. I noted the color coding on the wires and terminals, removed the two retainer screws, removed the old fan from the mounting bracket, installed the new fan using the rubber anti-vibration mounts, pressed -on the fan to the center drive shaft and re-installed the assembly to the back wall. I simply replaced the rear panels and shelves and plugged in the fridge. The only issue I had was the distance needed to press on the fan blade to preclude fan noise, which I found by trial and error, before re-installing the panels.
Was this helpful?
Thank you for voting!
Condensor motor was frozen
  • john from thibodaux, LA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip th e insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.
Was this helpful?
Thank you for voting!
Protective cover for bulb had melted
  • Lee from Brooklyn, NY
  • Very Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent i tems in the fridge from being able to touch. Bad solution.
Was this helpful?
Thank you for voting!
Condensor Fan going bad
  • George from Hickory, NC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
  • David from St. Pete Beach, FL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Was this helpful?
Thank you for voting!
Freezer was not getting cold enough
  • David from Salem, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and it works like its brand new. Thank you PartSelect!
Was this helpful?
Thank you for voting!
All Instructions for the 1068648621
121 - 135 of 176