- Home
- 10686399310
- Instructions
10686399310 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light switch went bad
-
Joseph T. from Morgantown, WV
- Really Easy
- Less than 15 mins
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Was this helpful?
Thank you for voting!
Hinge bracket between refrig and bottom freezer had broken. This is the part which keeps the door from opening too far.
-
Mary from Tillamook, OR
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Pla
... Read more
ce the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.
Read less
Was this helpful?
Thank you for voting!
Compressor having hard time kicking on
-
sarah from dearborn, MI
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.
Was this helpful?
Thank you for voting!
light switch sticking
-
Paula from Rush, NY
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this helpful?
Thank you for voting!
Light did not come on (bad bulb!) on TC18KL
-
Louis from Beloit, WI
- A Bit Difficult
- Less than 15 mins
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged th
... Read more
e unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.
Read less
Was this helpful?
Thank you for voting!
Broken rear wheel
-
daryl from Palm Harbor, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
I unplugged the unit Frist. Then I removed the grill covering the compressor and fan from the back. I then located the rear wheel and pin. I bent down the retaining tab and removed the pin and wheel. I installed new wheel and pin and bent retaining tab back to origional location. Replaced grill and checked unit for proper operation.
Was this helpful?
Thank you for voting!
No light in frig
-
Irene from Whitehall, MT
- Really Easy
- Less than 15 mins
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.
Was this helpful?
Thank you for voting!
Refrigerator was getting warm
-
Mack from Los Banos, CA
- Really Easy
- Less than 15 mins
Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.
Was this helpful?
Thank you for voting!
light would come on and off
-
Dora from Rock Island, IL
- Really Easy
- Less than 15 mins
Viewed the viedo - it showed what to do
Was this helpful?
Thank you for voting!
Frig not cooling.
-
Adam from Randolph, ME
- Really Easy
- Less than 15 mins
-
Pliers
After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.
Was this helpful?
Thank you for voting!
exchange of defective light rocker switch
-
Steve from River Edge, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Was this helpful?
Thank you for voting!
Light in the refrigerator didn't work
-
Anthony from Fairport, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Was this helpful?
Thank you for voting!
Freezer Ok. Refrigerator Not Cooling.
-
Donald from Kissimmee, FL
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Followed recommendations from others but went with most likely by percentage = defrost timer kit. Did not solve issue. Then went with bi-metal thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part ok. Then I saw on line that I should have listened for fan operation. I
... Read more
checked and found the fan motor to be defective. Replaced the motor and refrigerator worked fine. Both the motor and bi-metal thermostat were required. Should have checked fan operation first.
Read less
Was this helpful?
Thank you for voting!
refrigerator and freezer would stay frozen.
-
Jack from Poplarville, MS
- Really Easy
- More than 2 hours
I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.
Was this helpful?
Thank you for voting!