- Home
- 1068134792
- Instructions
1068134792 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
fridge door switch did not work
2 of 2 people
found this instruction helpful.
-
stu from richmond, VA
- Easy
- Less than 15 mins
-
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
My Kenmore Ice Maker stopped manufacturing ice
3 of 5 people
found this instruction helpful.
-
Kenneth from Philadelphia, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
The repair was very easy. I ordered the part from Part Seelect and the delivery was very quick.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one scre ... Read more w and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.
So easy to do a cave man could do it.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one scre ... Read more w and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.
So easy to do a cave man could do it.
Read less
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people
found this instruction helpful.
-
dorotea from staten island, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
Ice maker failed
2 of 2 people
found this instruction helpful.
-
Kim from Palo Alto, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Super easy! I read all these posts but here are a couple helpful hints -
1. to remove the old icemaker definitely remove the one lower screw but then unscrew the top two screws only half way. The top screw holes on the old and new icemakers are triangle shaped so the old icemaker will simply lift off the half-unscrewed top scr ... Read more ews. This makes reinstallation SO much easier.
2. carefully lower the loose icemaker enough to disconnect the wiring harness from the fridge and remove the old icemaker.
3. On installation the one thing to be careful with is the positioning of the fill tube. It's easier if it's in place when you reconnect the harness of the new icemaker because the harness is only as long as it must be.
4. hang the new icemaker on the half unscrewed top screws, snug them up, install the lower screw and flip the wire ice level sensor arm down.
I didn't even turn the water off because only a working icemaker can turn the water valve on and off.
Plugged in the power to the fridge and within an hour water filled the tray. By morning I had 2-3 batches of fresh ice in the bucket. Super easy.
1. to remove the old icemaker definitely remove the one lower screw but then unscrew the top two screws only half way. The top screw holes on the old and new icemakers are triangle shaped so the old icemaker will simply lift off the half-unscrewed top scr ... Read more ews. This makes reinstallation SO much easier.
2. carefully lower the loose icemaker enough to disconnect the wiring harness from the fridge and remove the old icemaker.
3. On installation the one thing to be careful with is the positioning of the fill tube. It's easier if it's in place when you reconnect the harness of the new icemaker because the harness is only as long as it must be.
4. hang the new icemaker on the half unscrewed top screws, snug them up, install the lower screw and flip the wire ice level sensor arm down.
I didn't even turn the water off because only a working icemaker can turn the water valve on and off.
Plugged in the power to the fridge and within an hour water filled the tray. By morning I had 2-3 batches of fresh ice in the bucket. Super easy.
Read less
Was this helpful?
Thank you for voting!
Unit froze up with ice in the cube maker
2 of 2 people
found this instruction helpful.
-
John from Mesa, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver
Just like the others. Unplug the refrigerator. Loosen the top two screw and remove the bottom screw. Unplug the unit, plug in the new one, slid the unit over the top two screws, replace the bottom screw and tighten the top two screws. Done. I ordered the unit Sunday it was shipped Monday and arrived Phoenix Wednesday, shipper then re
... Read more
routed it to Tucson Thursday who sent it back to Phoenix on Friday and finallydelivered it Saturday.
Read less
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people
found this instruction helpful.
-
Thomas from Roseville, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
Ice maker went bad
3 of 5 people
found this instruction helpful.
-
DENNIS from SOUTH LYON, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour
Had ice within 1 hour
Was this helpful?
Thank you for voting!
Unit wasn't producing ice
2 of 2 people
found this instruction helpful.
-
Michael from Ocoee, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reatta
... Read more
ched the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.
Read less
Was this helpful?
Thank you for voting!
Ice Maker started acting up
2 of 2 people
found this instruction helpful.
-
Bill from Sumas, WA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
Read less
Was this helpful?
Thank you for voting!
fans and lights worked in refrigerator but not cooling
9 of 23 people
found this instruction helpful.
-
James from Blue Springs, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
By going on line and going to PartsSelect, the check out procedures traced the problem to the start/overload relay. Using a nut driver, I removed the back panel and using their instruction, I installed the overload relay. On the next to the last step on the instruction, the sealer in the kit was already hardened. I called the service
... Read more
hot line at PartsSelect and they apologized and sent me another kit to finish the repair. In two days, the new kit came and the repair was complete. The whole experience with PartsSelect was great.
Read less
Was this helpful?
Thank you for voting!
Ice Maker Not Creating Ice Cubes
2 of 2 people
found this instruction helpful.
-
Daniel from Albuquerque, NM
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed Ice tray and flap followed by the three screws that held the old ice maker in place. (I probably didn't have to remove the top two, they are designed to just loosen and lift up on the mecanism to free.) I then pulled the old wiring harness out of the original ice maker. A small screw driver helped in depressing a tab while pulling
... Read more
on the harness. The same process was used to remove the wiring harness that was attached to the new replacement unit. I connected the original wiring harness that I had disconnected from the bad ice maker, and it fit perfectly into the replacement unit. No need to splice or use any of the harnesses that came with replacement. I tried installing the new unit and discovered that there was interfernce with the water feed hose. I had forgotten to break off the tab on the end of the replacement unit. Once I did that using pliers, the unit fit fine. I tightened the screws, installed the on/off mecanism and replaced the tray and flap. I then waited and waited, hoping to hear the forgotten sound of water entering the ice maker. Had a beer and walked the dogs thinking I had failed, but low and behold, over an hour later, the ice maker turned on the water. Many hours later, my wife woke me up in the middle of the night to declare we had cubes! Success.
Read less
Was this helpful?
Thank you for voting!
Ice maker not working
2 of 2 people
found this instruction helpful.
-
Dewey from Carrollton, GA
- Really Easy
- 30 - 60 mins
-
Nutdriver
First I turned off water supply. Then removed the two screws that attach ice maker, then disconnected the wiring harness.
Attached new ice maker in reverse order.
Attached new ice maker in reverse order.
Was this helpful?
Thank you for voting!
Broken plastic part at top of water fill tube to freezer
2 of 2 people
found this instruction helpful.
-
Jay from Mt. Pleasant, WI
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Simple. 1st, removed broken part to understand part (water fill tube to freezer, plastic part at top of fill tube cracked). 2nd go on your web site and look at prints to find part number, Study video to understand video. 3rd. Called customer service and lady was very nice and efficient. Placed order and received. Study video again a
... Read more
nd installed. My 9 year old grandson was visiting from out of town and assisted in installation. Just over 30 minutes to install
Read less
Was this helpful?
Thank you for voting!
Mounting bracket was riveted on old motor, mounting bracket holes on new motor were different
2 of 2 people
found this instruction helpful.
-
MIKE from ARLINGTON, OR
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
removed shims on screws holding motor together, enlarged hole in mounting bracket so motor screws could also go through mounting brackets.
Was this helpful?
Thank you for voting!
Original ice maker quit making ice, leaked water.
2 of 2 people
found this instruction helpful.
-
John from Yorba Linda, CA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.
It came in the mail, I got ... Read more home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.
Very nice kit, and economical compared to a new fridge!
It came in the mail, I got ... Read more home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.
Very nice kit, and economical compared to a new fridge!
Read less
Was this helpful?
Thank you for voting!