1068134792 Kenmore Refrigerator - Instructions

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

removed two screws and pulled part out of the unit. The local appliance store said they needed model and part # to try to identify and order the part. Found part select online, found the part immediately, ordered the part for $4.50 or so. Part was delivered in 2 days! Very easy installation and the part works perfectly. Thanks so muc ... Read more h!

I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in le ... Read more ss than 24 hours from my order placement.

Just like the others. Unplug the refrigerator. Loosen the top two screw and remove the bottom screw. Unplug the unit, plug in the new one, slid the unit over the top two screws, replace the bottom screw and tighten the top two screws. Done. I ordered the unit Sunday it was shipped Monday and arrived Phoenix Wednesday, shipper then re ... Read more routed it to Tucson Thursday who sent it back to Phoenix on Friday and finallydelivered it Saturday.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel

Very simple fix, remove 3 screws, two connectors to the old switch

Super easy! I read all these posts but here are a couple helpful hints -

1. to remove the old icemaker definitely remove the one lower screw but then unscrew the top two screws only half way. The top screw holes on the old and new icemakers are triangle shaped so the old icemaker will simply lift off the half-unscrewed top scr ... Read more ews. This makes reinstallation SO much easier.

2. carefully lower the loose icemaker enough to disconnect the wiring harness from the fridge and remove the old icemaker.

3. On installation the one thing to be careful with is the positioning of the fill tube. It's easier if it's in place when you reconnect the harness of the new icemaker because the harness is only as long as it must be.
4. hang the new icemaker on the half unscrewed top screws, snug them up, install the lower screw and flip the wire ice level sensor arm down.

I didn't even turn the water off because only a working icemaker can turn the water valve on and off.

Plugged in the power to the fridge and within an hour water filled the tray. By morning I had 2-3 batches of fresh ice in the bucket. Super easy.

First I removed the ice bin to give me room to work. Then I took out the screws that held the old ice maker in place. I disconnected the wiring. I then plugged the wires of the new ice maker into the old wiring harness. I put in the bottom screws and loosely connected the top screws. I checked the level of the ice maker with a small l ... Read more evel and then tightened the screws. The nest thing was to install wire level that shuts off the ice maker when the bin is full. Finally put the ice bin back in place.

Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

put arm up to stop icemaker from creating new ice cubes. us nut driver to unscrew 3 of the nuts holding icemaker in place do not completely remove the 2 top screws. lift off the screws and unplug from inside wire connection...make sure water tub is removed and frig unplugged. clean off ice anywhere inside freezer...take out new icemake ... Read more r and connect wire plug...attach icemaker on to the 2 top screws...use nut driver to tighten into place. add and tighten bottom screw...leave arm down...replace clean and dried water tube into back and make sure it slid into ice maker...tighten screws in back and attatch water hose to tube...plug frid back on slide back into place...will start making ice in an hr or so....

I used a phillips screw driver, took the old one off, replaced the new one and it worked immediately!!! Didn't have to turn anything off...fixed in 5 minutes for $11. Fantastic Experience and my husband was shocked. No repairman bill.

Ordered new ice maker from this site . Installation was very easy. Was happy to see that many electrical plugs were included. Chose the correct electrical plug and installed in 30 minutes. One note, be patient as it takes a while for ice maker to produce ice. When I heard the sound of ice dropping in the bin, I was very happy. Just in tim ... Read more e for summer cold drinks. :)

Used a nutdriver and removed the lower mount nut, then loosened the the top two nuts and the icemaker lifted off, then unplugged the device and replugged it into the "old" plug(the new ones were not needed) then remounted it. Then it did not fill (as others posted happened right away.) Some poster suggested manually filling the tray so I ... Read more did it. Later it froze and emptied and refilled and started working normally. Not sure if putting water had anything to do with it or it just took some time. It would be nice if the instructions addressed this issue.