1066680721 Kenmore Refrigerator - Instructions

All Instructions for the 1066680721
106 - 120 of 148

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
condenser motor broke
  • patrick from livonia, MI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.
Was this helpful?
Thank you for voting!
frosted evaperator
  • Burton from Mount ShaSTA, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.
Was this helpful?
Thank you for voting!
See below
  • Patricia from Hobe Sound, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The defrost timer that I ordered form you did the trick. My fridge was
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defe ctive. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you
Was this helpful?
Thank you for voting!
Refrigerator not cooling
  • Bryan from Midland, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Exactly how the part select video described it. Threw a little curve ball figuring out which timer setting to set it to. But the instructions provided with defrost timer walked me right through it. No problem. After installing part nothing happened for about ten minutes, which had me second guessing each and every step. Then, like magic, cold air began blowing. What a relief. Thanks so much, love this site. Refrigerator works like new!
Was this helpful?
Thank you for voting!
refridgerator was not cooling to the proper temps and finally would not cool at all
  • John from LAS CRUCES, NM
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Pulled refridgerator forward away from the wall. Remove the cardboard back behind the appliance.I saw that the condenser fan motor was not working. Unplugged the appliance from the electrical outlet. Removed a 3 wire plug from the condenser fan motor. Remove 3 screws (with a nut driver) which held the condenser fan motor in place. Remove the condenser fan motor from the appliance. Looked up the part needed for repair using the appliance model number. Found which part was applicable for the appliance. Placed the order from Price Select on a Monday morning and recieved the part 2 days later on Wednesday via FedEx. The item shipped was a 2 wire condenser fan motor. Read the instructions that came with the part. Using wire cutters, cut the old 3 wire plug. The center wire is a green and yellow striped wire. Use the same colored wire that is also shipped in the box and has connectors on both ends. Cut one of the connectors off and use the wire strippers to remove plastic wire coating. Connect both ends from the appliance and the green and yellow wire that was shipped. Use a wire nut (also shipped in the box) to connect the wires. You will have 2 black wires left on the new condenser fan motor that need to be connected to the appliance. You should have an orange colored wire and another wire that is black with a white stripe. Connect one wire from the new fan motor to the orange wire and use a wire nut to attach both wires together. Use the other black wire from the new fan motor to the black/white striped wire from the appliance. Use the wire nut to attach both those wires. Place the new condenser fan motor back in the appliance using the screws that come with the motor. Attach the green and white wire with the connector on the end to one of the 3 screws that hold the motor in place and secure the screws. Use the electical tape to hold the wires all together and away from the fan motor. Plug the appliance into the outlet. You can see the condenser fan motor working properly. Note that when connecting the 2 black wires from the new condenser fan motor to the orange and the black/white wire from the appliance, for my appliance, it did not matter which wires were connected as the fan motor was a clockwise motor. Place the cardboard appliance backing, back on to the appliance and push the refridgerator back in place. Allow about 5-6 hours to get the freezer to between 0-5 degrees. The refidgerator should be between 34-38 degrees and will take a little longer to get to that projected temp.
Was this helpful?
Thank you for voting!
Switch didn't work
  • Don from Laramie, WY
  • Easy
  • 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
How to get timer out of defrost cycle?
  • David from Virginia Beach, VA
  • A Bit Difficult
  • 15 - 30 mins
  • Socket set
Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.
Was this helpful?
Thank you for voting!
excessive water in condensate pan
  • michael from woodstock, MD
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
just as video instructions said, very easy just following them ,part arrived in very short time and was exact fit completely satisfied, saved repair man service charges and wait time
Was this helpful?
Thank you for voting!
Condensor fan motor quit working
  • David from New Albany, IN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.
Was this helpful?
Thank you for voting!
Condensor motor was frozen
  • john from thibodaux, LA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip th e insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.
Was this helpful?
Thank you for voting!
Condensor Fan going bad
  • George from Hickory, NC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!
Was this helpful?
Thank you for voting!
Both the freezer and bottom of refrig too hot
  • Marcia from Kansas, OK
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The blac k wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.
Was this helpful?
Thank you for voting!
Freezer was too cold and refrigerator was too warm
  • Jolinda from Eau Claire, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
After receiving the part, I watched the installation video on the PartSelect website. The step by step demonstration was excellent. I felt confident I could do it myself after watching the video just once, and utilizing the written instructions that came with the part. The installation went smoothly, and my refrigerator is functioning correctly again. Best of all, I did not have to go through the hassle and expense of hiring a repair person!
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
  • David from St. Pete Beach, FL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Was this helpful?
Thank you for voting!
Freezer was not getting cold enough
  • David from Salem, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and it works like its brand new. Thank you PartSelect!
Was this helpful?
Thank you for voting!
All Instructions for the 1066680721
106 - 120 of 148