1066680721 Kenmore Refrigerator - Instructions

All Instructions for the 1066680721
76 - 90 of 148

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator compartment warm
1 of 2 people found this instruction helpful.
  • alfonso from Fairfield, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
first confirm that freezer is cold. if is frozen solid it needs to be defrosted. take the freezer items out,take shelf out, bottom cover, 2 screws. then ice maker, 3 screws and unplug wires. then back panel 2 screws. In refrigerator compartment were the controllers are located, look under it you will see 1 hole, insert a flat end screw dr iver and turn clockwise till it stops. this action will turn on your defroster, also the compressor will stop. is the heater melting the ice? if so soak up water and clean tray, use hair dryer in drain hole to aid in the defrost, check tray under fridge and if its dry keep defrosting. it should take half an hour. now take the flat head screw driver and turn the defrost timer clock wise out of defrost mode a quarter turn or so. the compressor should come back on, soon after the fan in the freezer compartment should also come on. this steps lets you no that the defrost heater works, fan works and drain hole is clear. if its defrosted place parts back in the reverse order. if not defrosted replace heater or mother board. in refrigerator compartment were the dials are located their are 2 screws, one on the left and the other on the right side take them out, the cover will drop down, you will find wiring schematics you will need them to install defrost timer. is timer making ticking sound? if no replace timer. new timer will be different from original so follow instructions that come with it. timer is above were the hole is located. the plastic hold downs will break when you try to take them off, unplug fridge, lift timer out and remove from wire harness. the new timer has a black wire that slips over either 1 or 2 depending on color of wire on the wire harness. check schematics. some silicone adhesive will keep unit in place, ad some into the plastic shaft prior to installation, plug wire harness return wiring instruction along with new one inside of cover, plug in fridge, turn defrost timer clock wise with flat head screw driver making sure that you hold timer from above so it wont move. did compressor come on?. put all paper work inside of cover before installing cover
Was this helpful?
Thank you for voting!
freezer and food section too warm
1 of 2 people found this instruction helpful.
  • William from Milford, MA
  • Easy
  • 30 - 60 mins
  • Socket set
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this helpful?
Thank you for voting!
fan motor had gone bad
1 of 2 people found this instruction helpful.
  • william from whitwell, TN
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.
Was this helpful?
Thank you for voting!
Refrigerator would not stay cold
2 of 6 people found this instruction helpful.
  • Jeremy from State College, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench set
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Repl aced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Was this helpful?
Thank you for voting!
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
2 of 6 people found this instruction helpful.
  • James from Howell, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this helpful?
Thank you for voting!
light staying on
0 of 1 people found this instruction helpful.
  • Cecelia from Beaver Dam, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this helpful?
Thank you for voting!
took out old switch, replaced with new one from parts select.
0 of 1 people found this instruction helpful.
  • Jo Anne from Easley, SC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took out icemaker,it had been letting in too much water, foynd switch was not working anymore, ordered new one from PartSelect, got it in a few days,took icemaker out put new switch in & it is working like new. I was amazed I could still get parts for a 28 year old whirlpool. And with the help I got from PartSelect,I am really thankful. J oAnne, Easley, S.C.
Was this helpful?
Thank you for voting!
Internal light did not come on each time the door was opened.
0 of 1 people found this instruction helpful.
  • John from Jefferson Hills, PA
  • Really Easy
  • Less than 15 mins
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Was this helpful?
Thank you for voting!
rocker switch broke off
0 of 1 people found this instruction helpful.
  • STANLEY from OAKLAND, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.
Was this helpful?
Thank you for voting!
19 year old light switch broke
0 of 1 people found this instruction helpful.
  • Fred from Watertown, NY
  • Really Easy
  • Less than 15 mins
Great service. Unpluged old switch and pluged in new one. Works great
Was this helpful?
Thank you for voting!
Lights didn't always come on when was opened
0 of 1 people found this instruction helpful.
  • Gary from Jenkintown, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.
Was this helpful?
Thank you for voting!
Door Light switch cracked Mounting
0 of 1 people found this instruction helpful.
  • Paul from Hinsdale, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights we re staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Was this helpful?
Thank you for voting!
Replace Bad Switch
0 of 1 people found this instruction helpful.
  • carlos from haverstraw, NY
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place
Was this helpful?
Thank you for voting!
old switch left freezer bulb always-on
0 of 1 people found this instruction helpful.
  • JONATHAN from ELKINS PARK, PA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.
Was this helpful?
Thank you for voting!
light would work intermitently
0 of 1 people found this instruction helpful.
  • Gregory from middle island, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
Was this helpful?
Thank you for voting!
All Instructions for the 1066680721
76 - 90 of 148