1065669 Kenmore Refrigerator - Instructions

All Instructions for the 1065669
121 - 135 of 1430

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
icemaker quit working
16 of 22 people found this instruction helpful.
  • Kenneth from Aledo, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories ab out those guys!
Was this helpful?
Thank you for voting!
Fridge and freezer quit working
14 of 16 people found this instruction helpful.
  • Patrick from Rayland, OH
  • Easy
  • Less than 15 mins
  • Screw drivers
This is a side by side fridge. Both refrigerator and freezer quit working. I could here the combination start device click and try to start the compressor. It would shut back off within 5 seconds.Removed the lower rear cover on the fridge and cleaned the coils while it was off. Replaced the combination start device, plugged in the fridge , and it worked. What a relief!
Was this helpful?
Thank you for voting!
Ice maker quit making ice.
16 of 23 people found this instruction helpful.
  • Kearney from Port Allen, LA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Ice Maker quit working. Seemed like a water supply issue but when I read the other reviews, I decided to install and see. bolted the bracket on with three screws, slid in place. Nothing happened and about 10 minutes later, I heard the water release to the ise maker and have been making ice ever since.
Was this helpful?
Thank you for voting!
bad door gasket
14 of 17 people found this instruction helpful.
  • William from Palm Coast, FL
  • Very Easy
  • 30 - 60 mins
watched video. Very easy
Was this helpful?
Thank you for voting!
ice dispenser broken
17 of 26 people found this instruction helpful.
  • sandra from mechanicsville, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically i nclined,
Was this helpful?
Thank you for voting!
Refrigerator fans runs but compressor not running
13 of 14 people found this instruction helpful.
  • Marcus from Maylene, AL
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
MAKE SURE POWER IS OFF or REFRIGERATOR UNPLUGGED BEFORE STARTING THIS!!!
I removed the lower refrigerator backing. The compressor was located in the left corner of the refrigerator. I located the start device which had a thin clip on top of it. After removing the clip I pulled the 2 wires (Red and White) from the start device. I then pulled the whole device from the compressor. You can use a screwdriver to pry it from the compressor. I unplugged the capacitor from the old switch and plugged it into the new one. Installed in reverse from how I took it out.
Was this helpful?
Thank you for voting!
Old motor was not resetting back to proper position halting ice production.
13 of 14 people found this instruction helpful.
  • Kevin from Spring, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossref erenced to new part number which was correct the first try. Thank you!
Was this helpful?
Thank you for voting!
Broken cup water fill on ice maker
13 of 15 people found this instruction helpful.
  • Matthew from Aurora, CO
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt
Was this helpful?
Thank you for voting!
Constant 20 below zero in freezer (side by side ref/freezer) Ref 37 deg. OK. Defrost frozen up with ice.
14 of 18 people found this instruction helpful.
  • Dean from GRANBURY, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I watched several video's on youtube that showed me how to replace the parts. Just Google "how to fix my freezer". I figured the only problem was the freezer Thermistor so I only replaced it. The refrigerator has one to. Instantly the freezer went back to Zero degrees and the defroster works fine after melting all the ice in the bottom . Make sure the drain hole is cleared. I ordered the bi-metal thermostat just in case but I don't need it. Be sure and position the thermistor down in the freezer rail on the right side just to where you can see it in the first opening and pull it back up out of sight and tape it to the wall where it comes through from the air baffle. It's important that it's 7.8 " down from the top of the freezer. Happy now, Freezer 0, refrigerator 37. This thing use to run all the time, I'm saying electricity now.
Was this helpful?
Thank you for voting!
Ice maker would not fill with water
14 of 19 people found this instruction helpful.
  • John from Nicholasville, KY
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
Resistance on solenoid for water to ice maker measured low (5 ohms). I assumed the coil insulation had degraded because there was almost a short with such low resistance. Replaced the water inlet valve kit and ice maker filled with water and everything worked great. I had to cut the ends of the hoses because my model use compression f ittings and this new valve kit used the push on fittings. No leaks no problems. The cables plugged in the opposite direction from the old valve kit, so I had to re-route the cable a little and create slack by removing from 1 cable clamp.
Was this helpful?
Thank you for voting!
The water dispenser flow was very slow and the housing leaked when the filter was removed.
12 of 13 people found this instruction helpful.
  • Daniel from CAROL STREAM, IL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Removed front plastic grill and screws holding the filter in place. Also removed lower back cardboard panel to access water lines. Video on this website told me how to remove water lines from filter, you must depress a collar around the water line while pulling out the water line. Then install the new Water Filter Housing and water lines. The only problems I had was the tight space to work in and one of the water lines was leaking, but pushing the water line in further solved the problem.
Was this helpful?
Thank you for voting!
Shelf rails were broken so the crisper tray fell out
12 of 13 people found this instruction helpful.
  • Rita from Saint Charles, IL
  • Really Easy
  • Less than 15 mins
We removed the old shelf. Put the new shelf in place and slipped the crisper tray on the new rails of the replacemnet shelf. The crisper no longer falls off the broken rails when you open it. We noticed the replacemnet shelf has metal rails and the original had plastic which is probably why it broke after heavy use over 12 years.
Was this helpful?
Thank you for voting!
Old, cracked freezer door gasket
12 of 13 people found this instruction helpful.
  • Ken from ALBANY, OR
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
This is in a rental house; Refrigerator/freezer has been off for a few weeks so just opened the freezer door and used screwdriver to pry out one corner then pliers to grab and pull old gasket (seal) off. Had the new one laid out overnight to relax it; placed one corner on and then the opposite corner then repeated the other two corners. Positioned the keeper edge plastic all of the way around to place the gasket in the door. Closed the door to check the seal and plugged unit back in. Waited and then checked air temp with hand held IR temp gauge. All checked good, no cold spots anywhere. Piece of cake!
Was this helpful?
Thank you for voting!
The ice maker stopped working
16 of 25 people found this instruction helpful.
  • Duncan from Larchmont, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repai r man. He would have made two trips since he would never have had this part with him.
Was this helpful?
Thank you for voting!
No cooling, clicking noises like it trys to start!
17 of 28 people found this instruction helpful.
  • Luis from Montgomery, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
The star device that i recived was a little different, wasn't black like the original a recived a grey one and little bit smaller than the original but it fit perfect, and my frige is working good since i replaced.
Was this helpful?
Thank you for voting!
All Instructions for the 1065669
121 - 135 of 1430