1065666 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Magic Plus stopped making ice
25 of 35 people
found this instruction helpful.
-
George from Hammond, LA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the icemaker from the freezer by removing two horizontal screws holding it to the side wall, and one vertical screw holding the front to a bracket coming off the side wall. Then I used a flat screwdriver to unlock the electrical plug. (After doing this, I realized that this wasn't necessary at all, and this part could have
... Read more
been changed just as easily without removing the icemaker.) On the front, there is a white cover with Ice Maker Plus. Use a flat screwdriver to unlock the tangs and remove the cover. There are three screws in the corners that once removed, will allow the motor assy. to be gently pulled straight out. On the back of the part, you will see many gold lands that the timer touches. I don't think there was anything wrong with my motor. I had two spots where the gold plating was worn off, so I suspect it was not making contact, and the whole process would stop. Slide the new part in place making sure the teeth on the gears line up (not a big deal), and secure with the screws. Install cover and you're done. Mine has been making ice like it was brand new.
Read less
Was this helpful?
Thank you for voting!
plastic door shelf was cracked & couldn't hold any weight
20 of 20 people
found this instruction helpful.
-
Nancy from Hilton Head Island, SC
- Really Easy
- Less than 15 mins
looked up the model #, found your co. & ordered a new one Service was excellent, shipping reasonable; it was a pleasant surprise. I will tell my friends about your co.
Was this helpful?
Thank you for voting!
Refrigerator stop cooling
23 of 29 people
found this instruction helpful.
-
kelly from glen allen, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
I was about to waste $1000 on buying a Refrigerator. Took 1 mins to search on google "Refrigerator doesn't work". Found a video on youtube, showed a step and step video to solve my problem. Order the part $50 and it took me less then 5 mins to install it. =)
Was this helpful?
Thank you for voting!
Ice dispenser freezing up, dispenser door not closing completely.
22 of 26 people
found this instruction helpful.
-
Robert from Valencia, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainles
... Read more
s panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.
Read less
Was this helpful?
Thank you for voting!
The old resevoir needed to be replaced
35 of 68 people
found this instruction helpful.
-
Fred from Martinsburg, WV
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
The repair was incredibly easy -
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< ... Read more br />6. Drink water!
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< ... Read more br />6. Drink water!
Read less
Was this helpful?
Thank you for voting!
Refrigeator would not drfrost...
27 of 44 people
found this instruction helpful.
-
Curtis from Pikeville, KY
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you
... Read more
Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.
Thank you
Curtis Hall
Thank you
Curtis Hall
Read less
Was this helpful?
Thank you for voting!
Icemaker Failed After 2 Years Top Of Line Unit
20 of 24 people
found this instruction helpful.
-
JAMES from OCALA, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed plastic door over ice maker remove 4 screws and slide unit out after disconecting pull apart elect. Plug. Pop off side gear cover install on new and slide in, reconnecting electric plug as you go.
Was this helpful?
Thank you for voting!
ice would not fall from ice maker
22 of 30 people
found this instruction helpful.
-
Greg from Cary, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker
... Read more
from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.
Read less
Was this helpful?
Thank you for voting!
Ice door holder arm broken
20 of 26 people
found this instruction helpful.
-
Joseph S from Las Vegas, NV
- Easy
- 15 - 30 mins
-
Nutdriver
The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the pl
... Read more
astic arm, which caused the arm to fail. Then reassemble in reverse order.
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped working.
22 of 32 people
found this instruction helpful.
-
Scott from Fort Lauderdale, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed the icemaker to see if I could determine problem; motor was seized; got part numbers and ordered from you; parts arrived next day (even though overnight delivery wasnt' requested - so THANK YOU!); compared new parts to original to be sure of fit; reassembled unit; reinstalled in freezer, and waited for the sound of water filling t
... Read more
he tray. Producing like brand new again! Cancelled the service call w/ Sears for the following week (when it was convenient for them) Loved your service!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Ice machine wouldn't dispense ice from the door.
20 of 26 people
found this instruction helpful.
-
Linda from Jackson, MS
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the broken coupling with the new one from your store. It took less than 10 minutes. The video you provided on the website was very helpful.
Other Parts Used:
Was this helpful?
Thank you for voting!
Ice maker was flooding freezer
18 of 20 people
found this instruction helpful.
-
Raymond from Zwolle, LA
- Really Easy
- Less than 15 mins
-
Nutdriver, Wrench set
Replaced 8 cube ice maker assembly. Contrary to instructions I 1st removed 2 screws on the flapper door 2 removed 3 screws in bottom and 1 screw on right side bottom and pulled shelf out unplugged plug and lifted assembly off put new one on shelf plugged it in and slid it back into place replaceing. screws. was done in 10 min. start to f
... Read more
inish . so far seems to have solved the problem.
Read less
Was this helpful?
Thank you for voting!
Part imediately broke
21 of 29 people
found this instruction helpful.
-
STEVE from HUGHESVILLE, MD
- Very Difficult
- More than 2 hours
Dog chewes up the original part. Got the replacement , put it on the filter turned to lock in place and tried tp pull out old filter ( same procedure has been done multiple times successfully) part broke instantly upon putting pressure tom pull out filter. Sent back to you the next day for replacement.
Was this helpful?
Thank you for voting!
Ice maker would not stop making ice (Style 2)
17 of 18 people
found this instruction helpful.
-
James from Satellite Beach, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Taped plastic cover to get it out of the way with duct tape - removed three screws on each side - removed retaining screw for each module - carefully disengaged module using small flat head screw driver being sure to release the plastic retainer and then reverse the process. Be sure new modules snap into place.
Biggest problem ... Read more was initially figuring out what the problem was. Turning off the ice maker had no effect and it just kept making ice.
Biggest problem ... Read more was initially figuring out what the problem was. Turning off the ice maker had no effect and it just kept making ice.
Read less
Was this helpful?
Thank you for voting!
Ice maker auger motor runs but wouldn't dispense ice
17 of 18 people
found this instruction helpful.
-
Scott from Twin Falls, ID
- Really Easy
- Less than 15 mins
-
Socket set
My Kitchenaid side by side freezer has an ice dispenser on the door that would not dispense ice. The electronic door opened and the motor would come on with a repeated clicking noise. The Auger would turn with a few ice cubes in the bin, but not under load. After ruling out a clogged chute, I figured that the motor was stripped. The r
... Read more
od that turns the auger is a hexagon shaped piece, much like a screw driver you would use with your drill. After years of breaking down ice, it stripped the hexagon key in the motor, and would just spin under load. Now, PAY ATTENTION TO THIS PART. I looked online for a repair and saw a very similar motor repair that involved taking off the front panel and electronics. I did this, and ran into a solid piece of plastic with no way to get to the motor. I then looked at the inside of the freezer door more carefully. About 2/3 down I saw a small panel held in place by four 1/4 inch hex nuts. What was a 15 minute job, cost me over an hour removing and replacing the front of the freezer. Anyway, the replacement motor fixed the problem without a hitch, and now we have ice. Of note, this is the second repair of this ice maker system, after first having to replace the ice maker itself. And, this the second Kitchenaid built in refrigerator of this model as our first had ice maker issues and was returned as a recall. It is only 5 years old.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!