1065115 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would Not Make Ice.
8 of 10 people
found this instruction helpful.
-
Zach from Danville, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
After lots of internet exploring and diagnosis, the icemaker comes right out, and with three screws out and in, the job is all but done. Don't pay anyone for this repair!!!!!
Was this helpful?
Thank you for voting!
Ice maker gear broke into pieces
7 of 7 people
found this instruction helpful.
-
Joseph Keith from High Point, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
It was the right part at the right time. I had ordered parts through the retailer from Whirlpool but they were not right. I found the part number on the Whirlpool website and ordered it from you. Once it came it was a thirty second fix. Thanks.
J. Keith Miller
J. Keith Miller
Was this helpful?
Thank you for voting!
Water ?? filter needed to be replaced
9 of 13 people
found this instruction helpful.
-
Victor T from CORDOVA, TN
- Very Easy
- Less than 15 mins
Simple, turn and pull to remove. Push and turn to install.
Was this helpful?
Thank you for voting!
broken light switch in the freezer
7 of 7 people
found this instruction helpful.
-
kathleen from GREEN VALLEY, AZ
- Easy
- Less than 15 mins
-
Screw drivers
We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.
Was this helpful?
Thank you for voting!
Ice crusher not dispensing crushing ice or dispensing ice cubes
7 of 7 people
found this instruction helpful.
-
Robert from WESTFORD, MA
- Very Easy
- Less than 15 mins
-
Screw drivers
1. Remove the ice box
2. Unscrew the two Phillips screws on the base of the ice box compartment
3. Lift up the coupling and shaft (be careful because there is a spring between shaft and coupling and washer)
4. Remove old coupling
5. Replace with new coupling and remember to put back the spring
6. Insert back shaft ... Read more with coupling and washer
7. Screw back on the Phillips screws
8. Replace back the icebox
2. Unscrew the two Phillips screws on the base of the ice box compartment
3. Lift up the coupling and shaft (be careful because there is a spring between shaft and coupling and washer)
4. Remove old coupling
5. Replace with new coupling and remember to put back the spring
6. Insert back shaft ... Read more with coupling and washer
7. Screw back on the Phillips screws
8. Replace back the icebox
Read less
Was this helpful?
Thank you for voting!
light in refrigerator went OFF when in installed the new water filter
7 of 7 people
found this instruction helpful.
-
LUC from PALM DESERT, CA
- Very Easy
- Less than 15 mins
STRANGE ! to moment I installed the filter ALL the internal lights in my refrigerator went OFF and never came back.
Strange !! refrigerator works fine but no more light in it !!
My email is : [email protected]
DON'T USE earthlink email anymore
Strange !! refrigerator works fine but no more light in it !!
My email is : [email protected]
DON'T USE earthlink email anymore
Was this helpful?
Thank you for voting!
The Freezer defrosted and everything on the top and the bottom spoiled
10 of 16 people
found this instruction helpful.
-
Jorge from Miami, FL
- Easy
- 15 - 30 mins
-
Nutdriver
i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burn
... Read more
ed. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.
Read less
Was this helpful?
Thank you for voting!
Reset rater filter
7 of 8 people
found this instruction helpful.
-
Andre from GRAND RAPIDS, MI
- Very Easy
- Less than 15 mins
Hold both water filter reset touch sensors down together. This will reset the water sensor indicator.
Was this helpful?
Thank you for voting!
light not working in fridge
7 of 8 people
found this instruction helpful.
-
Michael from East Meadow, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
It was so easy!
Thanks for the rush to my home on the part.
I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!
Easy!
And I am not Mr. Fix-it!
Thanks for the rush to my home on the part.
I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!
Easy!
And I am not Mr. Fix-it!
Was this helpful?
Thank you for voting!
Warm ref and frz
6 of 6 people
found this instruction helpful.
-
Peter from MASSAPEQUA PK, NY
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
Removed old starter and capacitor as per your website instruction.
Plugged in new parts.
Compresser turned on
Plugged in new parts.
Compresser turned on
Other Parts Used:
Was this helpful?
Thank you for voting!
Stopped cooling/freezing
6 of 6 people
found this instruction helpful.
-
Roper from PALM BAY, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
It is as easy as is shown in the self-help video. (1) Disconnect the power, (2) Roll the appliance out so you can get to the back, (3) Using a nut driver remove all the screws from the lower back panel then remove the panel, (4) Remove the tensioner wire, (5) unplug the electrical connection to the capacitor, (6) gently but firmly remove
... Read more
the capacitor and starter relay as one unit, (7) preassemble your new capacitor and starter relay as one unit, (8) now simply reverse your steps for installing and you are done! These two parts saved me the cost of a new refrigerator. Almost as easy as changing a light bulb. PS: while you have the panel removed you can do a thorough cleaning with a soft brush and vacuum.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Changed air filter
6 of 7 people
found this instruction helpful.
-
Tom from LONGMONT, CO
- Very Easy
- Less than 15 mins
Very simple, easy, and quick! Anybody can do it!!
Was this helpful?
Thank you for voting!
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
7 of 10 people
found this instruction helpful.
-
Antonio from San Antonio, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this helpful?
Thank you for voting!
Broken ice bin coupling
7 of 11 people
found this instruction helpful.
-
Bradley from Woodstock, MD
- Really Easy
- Less than 15 mins
Online parts detail made identifiying the correct part very easy. $10 fix instead of a $150 service call. Once the right part was identified, fixing it was very easy.
Was this helpful?
Thank you for voting!
Ice maker just stpooed making ice
5 of 5 people
found this instruction helpful.
-
Cuong from Camarillo, CA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind th
... Read more
e picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.
The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.
The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.
Read less
Was this helpful?
Thank you for voting!