10650212011 Kenmore Refrigerator - Instructions

The how to video told me what to check to determine what part was probably broken. Then another video showed me how to take it apart. It gave me the name, number, and a photo of the part. I ordered it from Part Select without even checking with another retailer since they gave me the information to do it myself, saving me lots of $ for repair labor costs! Then I watched the repair video again and put it back together! It works! It was simple and I really appreciate this service! Thank You

The repair went extreamly easy and exact to detail. I followed the video step by step, and that turned the assembly into a professional job.

Remove drip pan from indoor ice dispensing system remove to bottom screws holding dispenser faceplate .lift faceplate out of the way exposing the bracket and ice and water dispenser micro switches be careful in removing microswitch, the one I removed came apart and had a little difficulty putting it back together ,used super glue and fix that problem. No instructions came with bracket so take your time. This is a relatively simple job any one should be able to do it.

I surfed partselect and read that a reader had a similar problem with a rattling fan. I then removed the back panel, after I had unplugged the unit, and was able to feel the slop in the fan shaft. I then watched the video of how to replace the fan and ordered the part soon after. The part arrived 3 days later! Easy to do. I was finished in 12 minutes and the fridge runs silently. The part of the job that took the longest was vaccuming the undercarriage. There was alot of dust! Couldn't have helped the efficiency on the fridge. Keep it clean.

I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

Per instructions in video. Super easy. Spent 45 min. cleaning ice/water dispenser and ice maker tray. Spent 15 min. replacing ice door.

Watched your installation how to video. Applied same procedure. Went smoothly.

Followed the DYI Video provided by partselect. Best advice, take a digital pic prior to disasembly, which of course I didn't! My cordless screw driver w/o the tip, is the same size as the screws thus no need for a nut driver.

I had two repair problems. #1- Ice door kit & #2 control bracket. I followed the instructional video and completed repair in under 30 minutes. I surprised myself and had a happy wife.

I saw a video of it, and simply took apart the ice maker and put the new Auger Drum in, then reassembled the ice maker.

One day the ice cream in the freezer seemed mushy, but the ice was still frozen. There was not water in the ice bin. However, the problem resolved itself. This suggested that the defrost timer had become stuck for an extended time, but then continued to run. The fact that the freezer went back to frozen, implies that all the components of the cooling loop (compressor, condenser & fan, evaporator & fan) were fine. It was possible that the problem was caused by a bad defrost (?evaporator?) thermostat but everything I saw on line suggested that the defrost timer is the culprit about 40 - 50% of the time. Anyway, I followed the instructions in the on-line video at this site for replacing the defrost timer and it was easy. It would have only taken 15 minutes, but I spent a while reading the defrost timer instructions and hunting down a schematic for my refrigerator, to determine which pin the loose wire should go on.

Removed outer cover. Removed control bracket which holds the water/ice dispenser paddles. Removed paddles from old/broken bracket, plastic pins were broken where the paddles hinge. Placed on new bracket placed screws and it was done. Very simple repair. Part cost less then $18.00 including shipping. Saved me mucho dollars!!!!

hardest part getting the putty knife in right place to pop off cover---found the plastic bracket was broken where the switch was held in place---- so ordered new switches and bracket ---- got the parts in 3 days--good service--easy job 2 do and saved lots of $$$$$$$$---

First unpluged the electrical service cord,turned the water off to the appliance Removed water line.removed 2 screws holding the valve to the appliance,unpluged the water lines to the ice maker and water dispencer,discarded old valve then just replaced the new valve, it works perfectly. How did you get it here so fast? I ordered it one day and it was here the next day, I was expecting to wait at least 3 to 5 days, very pleased with your quick service. Thanks a lot, Jimmy