10642 Kenmore - Instructions

All Instructions for the 10642
121 - 135 of 581

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door would pop open. I cleaned gasket made sure nothing in the way of door. Gasket was cracked top and bottom it worked better but the seal was not good.
2 of 2 people found this instruction helpful.
  • Roy from KAUFMAN, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Did just like the video showed took doors off daughter helped take off doors so easy put door on blanket. My daughter 38 went to town putting it on just watch the corners so easy two days after installation the door seals great. You can do this.
Was this helpful?
Thank you for voting!
Refrigerator was very noisy. Investigation revealed that the condensor fan motor was going bad.
2 of 2 people found this instruction helpful.
  • DANIEL B. from ROCHESTER, IN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
First let me say that the instructional video on your website for this repair was very informative. My son and I watched that before we began the repair. We unplugged the unit first. After removing the back cover, he unplugged the old fan's electrical connection, and then proceeded to remove the fan and bracket from the unit. We then removed the old fan from the bracket, installed the new one and then he reinstalled the new fan and bracket back into the unit. He used the included electric adaptor cable to complete the electrical connection, plugged in the refrigerator briefly to confirm all was well (it was), then replaced the back cover and we were done.
Was this helpful?
Thank you for voting!
Ice maker clicked CW and CCW, but did not make ice
2 of 2 people found this instruction helpful.
  • Louis from BASKING RIDGE, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Replaced the control of the ice maker assembly.
Was this helpful?
Thank you for voting!
ice maker gears stripped/ bearing & cup assy broken
3 of 5 people found this instruction helpful.
  • Timothy from Lake Geneva, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The bearing & cup assembly was broken and the gears in the drive assy were stripped. Unfortunately I couldn't find anywhere to buy the gears without buying the entire motor assy with the gear box already on it. Cost was up to $85 with shipping but at least it now works fine.

To repair: a 1/4 nut driver will take off screw b elow ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.
Was this helpful?
Thank you for voting!
The coating on the mold /heater unit as cracked and some broken off and cause the water to drip down in the Ice trace and form large icicles
3 of 5 people found this instruction helpful.
  • James from Tomball, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
Was this helpful?
Thank you for voting!
Condenser motor was making noise.
4 of 8 people found this instruction helpful.
  • Joe from Spring Hill, TN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Socket set
Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.
Was this helpful?
Thank you for voting!
After 17 years, the old door gasket was split and showing signs of mold
2 of 2 people found this instruction helpful.
  • duncan from HOWELL, NJ
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
The gasket has an inner lip that fits over the edge of the door plastic liner. The old gasket was removed by pulling it straight out, in the plane of the door. Try not to pull sideways as it could crack the door liner, which gets brittle with age. The new liner had a brown magnetic strip, which holds the door closed, and this fits behi nd the edge of the door liner. Start on the bottom of the door. A helper is useful to hold the gasket loosely vertical. A flat blade screwdriver can be used to pry away the liner to insert the new seal. Once you have worked in the lower edge, install both sides, and then the top. Some juggling side-to-side may be needed for an exact fit
Was this helpful?
Thank you for voting!
Faulty light socket
3 of 5 people found this instruction helpful.
  • Larry from HOUSTON, TX
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!
Drain clogging causing water to leak bottom of fridge
2 of 2 people found this instruction helpful.
  • Ted C from DSRT HOT SPGS, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.
Was this helpful?
Thank you for voting!
Refer not running.
2 of 2 people found this instruction helpful.
  • Gizella from PLACENTIA, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
1) Went to site. 2)Read trouble shooting section for recommended replacement part. 3)Selected part. 4) Watched detailed installation video on part specifications. 5)Installed part. Refer runs like new. (Note: May have to restart installation video if audio does not work the first time.)
Was this helpful?
Thank you for voting!
Ice maker failure to produce ice
2 of 2 people found this instruction helpful.
  • Conley from richmond, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
The repair was simple.

I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.

removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!

$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.

I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!
Was this helpful?
Thank you for voting!
Ice maker stopped making ice
2 of 2 people found this instruction helpful.
  • Sean from Lancster, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.
Was this helpful?
Thank you for voting!
icemaker wasn't making ice
2 of 2 people found this instruction helpful.
  • JAMIE from HANOVER, PA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people found this instruction helpful.
  • dorotea from staten island, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
replaced motor and fan
3 of 5 people found this instruction helpful.
  • Rex from Amarillo, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.
Was this helpful?
Thank you for voting!
All Instructions for the 10642
121 - 135 of 581