10642 Kenmore - Instructions

All Instructions for the 10642
106 - 120 of 581

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
gasket was cut and ripped
3 of 3 people found this instruction helpful.
  • Herbert from NIAGARA FALLS, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
rippped the old one off and carfully put the new one on with a flat head screwdriver at an angle as not to rip the new one
Was this helpful?
Thank you for voting!
freezing everything
3 of 3 people found this instruction helpful.
  • Darcie from VINELAND, NJ
  • Difficult
  • 30 - 60 mins
Removed old gasket. Wiped everything down. Popped in new gasket.
It was a little tedious, but it went in easy enough. Some reviews said the new gasket was kinked and bent. Mine I am happy to say was smooth. Some things are still getting quite cold like vegetables and ginger ale.(almost freezing). But it is way better than it was. Sa ved us from having to purchase another refrigerator. The fellow who helped me made it easy to order and everything went smoothly. I appreciate the help and patience you provided.
I
Was this helpful?
Thank you for voting!
water leaking in fridge and ice buildup
3 of 3 people found this instruction helpful.
  • Darrell from VALPARAISO, IN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
replacement went easy most of the time was spent removing the ice build up
Was this helpful?
Thank you for voting!
Stopped Making Ice
4 of 6 people found this instruction helpful.
  • WARREN from JACKSONVILLE, OR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Followed on line video
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people found this instruction helpful.
  • THOMAS from WILLARD, OH
  • Really Easy
  • Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
3 of 4 people found this instruction helpful.
  • David from Hemet, CA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this helpful?
Thank you for voting!
Ice maker would not turn off. Kept making ice! Even turned off all water to house, but then realized that ice maker was being fed by pressurized RO tank!!
4 of 7 people found this instruction helpful.
  • Keith from Green Valley, AZ
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Broken plastic part in motor assembly. Very simple to replace. Sears wanted $322.00!!!
Was this helpful?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people found this instruction helpful.
  • anthony from HAVELOCK, NC
  • Really Easy
  • 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
the light socket broke apart
4 of 7 people found this instruction helpful.
  • Elyse from Skokie, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this helpful?
Thank you for voting!
a rumbling noise was comming from the back of the fridge
3 of 4 people found this instruction helpful.
  • Craig from Birchwood, TN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembl y,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket
Was this helpful?
Thank you for voting!
ice maker gears stripped/ bearing & cup assy broken
3 of 5 people found this instruction helpful.
  • Timothy from Lake Geneva, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The bearing & cup assembly was broken and the gears in the drive assy were stripped. Unfortunately I couldn't find anywhere to buy the gears without buying the entire motor assy with the gear box already on it. Cost was up to $85 with shipping but at least it now works fine.

To repair: a 1/4 nut driver will take off screw b elow ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.
Was this helpful?
Thank you for voting!
The coating on the mold /heater unit as cracked and some broken off and cause the water to drip down in the Ice trace and form large icicles
3 of 5 people found this instruction helpful.
  • James from Tomball, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
Was this helpful?
Thank you for voting!
Condenser motor was making noise.
4 of 8 people found this instruction helpful.
  • Joe from Spring Hill, TN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Socket set
Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.
Was this helpful?
Thank you for voting!
After 17 years, the old door gasket was split and showing signs of mold
2 of 2 people found this instruction helpful.
  • duncan from HOWELL, NJ
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
The gasket has an inner lip that fits over the edge of the door plastic liner. The old gasket was removed by pulling it straight out, in the plane of the door. Try not to pull sideways as it could crack the door liner, which gets brittle with age. The new liner had a brown magnetic strip, which holds the door closed, and this fits behi nd the edge of the door liner. Start on the bottom of the door. A helper is useful to hold the gasket loosely vertical. A flat blade screwdriver can be used to pry away the liner to insert the new seal. Once you have worked in the lower edge, install both sides, and then the top. Some juggling side-to-side may be needed for an exact fit
Was this helpful?
Thank you for voting!
Faulty light socket
3 of 5 people found this instruction helpful.
  • Larry from HOUSTON, TX
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!
All Instructions for the 10642
106 - 120 of 581