1058 - Instructions

replaced lights in refrigirator and freezer

Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.

Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .

disassembled bottom trim on oven door.cleaned area of excess rust and installed trim piece.

I simply replaced the element. HOWEVER, the most wonderful parts of this repair...Because of the pictures and closeups and descriptions I knew exactly 'what' to order! And I had the replacement in less than 24 hours. I can do some home repairs but this company provided such detailed information AND speed of delivery...that this was a no-f ... Read more uss fix. I'll definitely stop by to buy, again. Thanks!

hand tightened with threads into threaded insert

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer ... Read more works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.

Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem ... Read more as to what to do. The unit is working great now.

Pulled the old seal out, replaced it with seal #391483S and so far looking good !

Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering ... Read more the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.

remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.

Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to ... Read more new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.

All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or ... Read more it will not come on.