10336 - Instructions

All Instructions for the 10336
121 - 135 of 222

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not light
0 of 1 people found this instruction helpful.
  • Robert from Joliet, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I removed the oven door, racks, and oven floor. That was easy, the floor had two thumb screws and one phillips/hex screw. I removed the lower drawer and the 2 covers above the drawer. The igniter was held in place by two phillips/hex screws. Had to manuver a bit to get the right angle to remove the screws. THE MOST IMPORTANT PART OF THE REPAIR, when you cut the two wires to remove the old igniter, cut them off as close to the old igniter module as possible. On my stove one of the wires on the new igniter was about an inch too short and I had to add a section of wire. Overall the whole job was easy. Keep track of screws as you remove them.
Was this helpful?
Thank you for voting!
The electric igniter wore out - broiler burner
0 of 1 people found this instruction helpful.
  • Andrew from Woburn, MA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I open the oven, then pulled out the racks. I went on to remove the bottom pan by removing 2 screws from the back.. I then removed the broiler burner and disconnected the wires from the relay. I unscrewed the igniter and replaced it. I stripped the wires and connected the old connectors using the ceramic wire nuts. I put the burner back in place and connected the wiring.. I then trested the unit to make sure it worked . . .it did. I replaced the bottom pan and racks and once again made sure everything was working right.

Job done.
Was this helpful?
Thank you for voting!
lower igniter dead
0 of 1 people found this instruction helpful.
  • Glen from Medford, MA
  • A Bit Difficult
  • 15 - 30 mins
With directions from the website as well as in the box, the repair was almost flawless. I needed to be a mouse with a 6mm box-end wrench.
Was this helpful?
Thank you for voting!
Oven bottom burner would not light
0 of 1 people found this instruction helpful.
  • Doreen from Lansdale, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I removed the bottom drawer, disconnected the wires and then using the socket driver removed the screws holding the burner in place from below. I then unscrewed the bottom plate of the oven from the top so I could get to the burner. I unscrewed the one screw still holding the burner in place. Disconnected the old igniter and then cut t he cables at an appropriate length so I could re-use the connectors on new igniter. Spliced together using wire nuts provided, mounted new igniter to burner, put it all back together and it fired up like it was new.
Was this helpful?
Thank you for voting!
oven igniter quit working
0 of 1 people found this instruction helpful.
  • Paul from New Hampton, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I removed the oven grates and removed 2 screws that held the bottom pan in the oven to get easy access to the burner and igniter. Remove 2 screws that held the burner in place. Removed wire nuts. Removing burner allowed easy access to fasteners holding ignitre in place. Confirmed that the igniter was bad by checking the continuity. Or dered part later in the evening from parts select. Part was here 2nd morning after I ordered it. Installed, and checked to make sure igniter wasworking properely. When check confirmed igniter was working, replace oven components. Saved myself $100 or more by doing it myself rather than having a repairman out.
Was this helpful?
Thank you for voting!
Gas Oven would not lite - broiler and top burners operate
0 of 1 people found this instruction helpful.
  • John from Mentor, OH
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
The stories posted on your web page are great - only improvement would to add a schematic of the parts being removed - no issues were encountered - great service by the way - part arrived the next day - a Saturday!

John M.
Was this helpful?
Thank you for voting!
oven would not start,
0 of 1 people found this instruction helpful.
  • Douglas from LaMoille, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, i gniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?
Was this helpful?
Thank you for voting!
oven would not light.
0 of 1 people found this instruction helpful.
  • Chad from Hanford, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
simple remove & replace. 2 min job. Couldn't be happier.
Was this helpful?
Thank you for voting!
The oven would not ignite
0 of 1 people found this instruction helpful.
  • Richard from Las Vegas, NV
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
I took the old igniter out and replaced it with a new one.
Was this helpful?
Thank you for voting!
Bake glow coil will not come on (Glow)
0 of 1 people found this instruction helpful.
  • Bernie from Cedar Grove, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off
Was this helpful?
Thank you for voting!
Old igniter failed
0 of 1 people found this instruction helpful.
  • Greg from Yuma, AZ
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!
Was this helpful?
Thank you for voting!
oven would not lite
0 of 1 people found this instruction helpful.
  • albert from amston, CT
  • Easy
  • 15 - 30 mins
  • Socket set
frist tested ignitor with meter removed ignitor order
part , I recieved to my surprise next day I'm a very happy person
Was this helpful?
Thank you for voting!
igniter burned up
0 of 1 people found this instruction helpful.
  • Alita from Boothwyn, AL
  • Easy
  • 15 - 30 mins
  • Nutdriver
The biggest problem is to get down low enough and far enough back to be able to reach the igniter. Other tan that , it was a simple affair.Unscrew the old one and detach the wire nuts and reverse the procedure for the installation and hope the gas valve has'nt been affected
Was this helpful?
Thank you for voting!
Oven worked but broiler wouldn't work
0 of 1 people found this instruction helpful.
  • Rodney from Rio Vista, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver
Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstal led protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.
Was this helpful?
Thank you for voting!
No Oven Flame
0 of 1 people found this instruction helpful.
  • laura from Shelton, CT
  • Easy
  • 30 - 60 mins
  • Nutdriver
Take bottom drawer out, take two 1\4 inch drive screws out from back bottom of inside of oven. Take out protector plate . Remove 1\4 inch drive screws from bottom burner[back of oven] where drawer was. Extract burner. Rest is self explanitory. Good luck. . . . . .
Was this helpful?
Thank you for voting!
All Instructions for the 10336
121 - 135 of 222