10336 - Instructions

All Instructions for the 10336
106 - 120 of 222

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
gas oven electric igniter
0 of 1 people found this instruction helpful.
  • Dennis from Show Low, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Wrench set
1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy
Was this helpful?
Thank you for voting!
Igniter would not go on to lite the burner
0 of 1 people found this instruction helpful.
  • joseph from Ozone Park, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
took the bottom plates off with philips screwdriver.(note) there are two plates..outter and inner..to get to the two screws on the igniter.Remove igniter(two nuts). Install new. Cut the wires from old(lower part of oven and rewire with porclain wire nuts.Very simple...Partselect was great too..very fast shipping. Will do buisness again.
Was this helpful?
Thank you for voting!
broiler worked but oven didn't
0 of 1 people found this instruction helpful.
  • Mary from Pekin, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
We follow the advise of one of you other viewers. It was so easy. Our thanks for the info and the speeding delivery
Was this helpful?
Thank you for voting!
oven would not light.
0 of 1 people found this instruction helpful.
  • Thomas from Port Huron, MI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I removed the oven burner while the igniter attached. put unit on my bench and changed the igniter and reinstalled the burner and reattached the wires to the supply terminals. Tested the unit and it lite up ok.
Was this helpful?
Thank you for voting!
oven without heat
0 of 1 people found this instruction helpful.
  • karen from Chicago, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Took off the 2 bottom covers, saw the igniter did'nt glow, checked for voltage,yes.Ordered part. when had part,pulled out ignitor,respliced wires, and did in reverse order.
Was this helpful?
Thank you for voting!
Igniter didnt work
0 of 1 people found this instruction helpful.
  • Philip from Lyndhurst, NJ
  • A Bit Difficult
  • 15 - 30 mins
  • Socket set
I took out the racks, unscrewed the bottom cover, removed the bottom drawer, cut the leads for the igniter, removed the bad one, had a little difficulty installing the new one, the screws were a little longer than the old ones, and were a little hard to get at, rewired the the leads, and put everything back, and started it up and it worke d great!
Was this helpful?
Thank you for voting!
igniter burned out
0 of 1 people found this instruction helpful.
  • Dwight from Angola, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
followed peoples advices and all went very smooth. make sure to undo bracket from behind bottom drawer as it will make your life much easier.
Was this helpful?
Thank you for voting!
ovens ignitor went out as they so often do...
0 of 1 people found this instruction helpful.
  • Brian from Las Vegas, NV
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I first checked the power by pushing oven button, I heard the relay make a sound " CLICK" ,I then knew it wasnt the power .I then removed the oven racks and then I removed the the two screws holding the pan in place. I hit the power button and noticed the ignitor did not glow as it should.I ordered the part and replaced it and had froze n pizza 20 minutes later.
Was this helpful?
Thank you for voting!
Oven Igniter failure
0 of 1 people found this instruction helpful.
  • Fergus from Racine, WI
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
This site provides excellent instructions and saved a lot of time and effort.

Replacing the part only requires basic skills and attention to detail. The kit I received included ceramic wire nuts to splice the new igniter to the old connections. Be sure to leave enough wire to mke the connections properly.
Was this helpful?
Thank you for voting!
Broiler worked but oven would not
0 of 1 people found this instruction helpful.
  • Frank from Taylorville, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I first read and printed out several postings on how others did the job. I read and re-read them and then I started. I cut power to stove and left gas on. I removed door, pushed back and removed bottom burner cover. I exposed the igniter which I deduced was the problem. I removed the front burner screw and the rear screws (2) and the burn er came out very easy. I removed the igniter from the burner, made sure which wire went where (I marked them)an snipped them. I used the ceramic caps and spliced the wires. I replaced the burner and turned on the power. I turned the oven knob on and "Viola", the igniter came on and burner came to life. I replaced every thing in reverse order and called it "done". It was so easy with the postings on this subject.
Was this helpful?
Thank you for voting!
Oven refused to light checked all connections suspected the igniter was bad
0 of 1 people found this instruction helpful.
  • Robert from lebanon, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver
Removed bottom drawer removed door and racks and bottom shield.disconected two leads from igniter . then struggled to remove igniter. after ordering part readf comments from other men and the man who said he removed the burner hit it right on the head after the part arrived the very next day after ordering it i removed the burner attached pig tails and had part installed and stove back together in 15 minutes. thanks good experience
Was this helpful?
Thank you for voting!
oven does not heat - top burners work - broiler works
0 of 1 people found this instruction helpful.
  • Paul C from Bradenton, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
1) use screwdriver to remove screws securing lower pan in oven (screws are at back of oven)
2) remove lower pain to expose igniter and burner
3) remove lower storage drawer
4) disconnect 2 igniter wires from where they are attached underneath
5) use nutdriver to remove burner from above and below (this makes it easier to remove the igniter)
6) use nutdriver to remove the faulty igniter
7) cut off clips from faulty igniter leaving enough length to strip and then attach with ceramic caps to new igniter. (be sure you attach the right clip to the right wire)
8) reverse the process to install the new igniter.
20 minutes tops
Was this helpful?
Thank you for voting!
Gas oven stopped working (no heat).
0 of 1 people found this instruction helpful.
  • Jackie from Brunswick, ME
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
The range still worked and the broiler still worked. I noticed that the ignitor for the broiler turned on and glowed a short time after starting the broiler. I dissembled the floor of the oven (just two screws) and tried the same for the oven, but the ignitor did not start or glow. I ordered the part. It was sent withing two days. It was easy to replace and the oven has worked well since. I recommend ordering the attachment fixture as well, in that taking apart the one that held the old ignitor immediately stripped a screw and I ended up bending the fixture and having to reshape it (the small extra cost will be very well worthwhile!)
Was this helpful?
Thank you for voting!
The oven would not heat.
0 of 1 people found this instruction helpful.
  • Gloria from Edmond, OK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
We found the part right away from the diagram provided by your web site. We located the part number easily, paid on line and received in part in two days. My husband fixed it. It was relatively easy. Saved us money to pay someone to fix it. It could easily cost us more than $200.
Was this helpful?
Thank you for voting!
Sunday night 4 days before thanksgiving oven wont light
0 of 1 people found this instruction helpful.
  • Nicholas from Palmyra, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Wrench set
Part arrived day before thanksgiving bent old igniter back and forth till broke off then easily took out screws.Cut and strip old wire, screw on new ignighter this was tough to get a wrench on with the positioning but after connecting those wires and slappin the rest of the oven back together one turn of the temp knob told me thanksgiving was going to happen Thanks to part select I was lookin like a hero!
Was this helpful?
Thank you for voting!
All Instructions for the 10336
106 - 120 of 222