1028B Roper Range - Instructions

All Instructions for the 1028B
31 - 45 of 49

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower oven Igniter wouldn't heat up and fire the propane.
1 person found this instruction helpful.
  • Michael from CHEWELAH, WA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Called repair man and described the problem. He said I could do it myself. PartSelect had the part and a previous description on the PartSelect site told me how to do the repair. It was easy. Be careful when removing the igniter nuts. I used a very small amount of sewing machine oil so as not to strip the threads. works great.
Was this helpful?
Thank you for voting!
surface element out
1 person found this instruction helpful.
  • Edward from TAYLORS, SC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplug from outlet and top remove back section of range and unplug wiring from switch, remove knob and unscrew two screws and remove old switch. Install new switch reinstall screws and plug switch plugs into new switch (will only go on the correct way). reattach back and plug into outlet. All done and surface element works perfectly.
Was this helpful?
Thank you for voting!
8" FRONT BURNER STAYED ON HIGH HEAT/WOULD NOT REDUCE TEMPERTURE
1 person found this instruction helpful.
  • RICHARD from DELTONA, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
REMOVE BACK OF RANGE, REMOVE BURNER KNOB. REMOVE SWITCH CONTROL REMOVE WIRES. REPLACE WIRES ON NEW SWITCH. INSERTED ALL WIRES REPLACE NEW SWITCH RE REPLACE ALL SCREWS. CHECK SWITCH. TURN BRAKER BACK ON. CHECK SWITCH FUNCTION. ALL IS FINE. PUT BACK ON RANGE SCREW IT IN PLACE. MOVE RANGE BACK IN IT POSITION.
Was this helpful?
Thank you for voting!
Right front burner would only stay on high
1 person found this instruction helpful.
  • Brian from YORK HAVEN, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Turned off breaker, pulled stove from wall, took off knob, unscrewed and pull off backing from stove, unscrewed heat control part, unplugged wires, plugged into new part, installed part, replaced stove backing, replaced knob, pushed stove back in place and turned on breaker. It worked fine.
Was this helpful?
Thank you for voting!
replaced oven igniter
1 of 2 people found this instruction helpful.
  • Lynn from LEWISTON, MI
  • Very Easy
  • Less than 15 mins
  • Screw drivers
this was so simple.. attach with 2 screws and plug in and done.. less than a minute.. to be honest it took me longer to put the oven back together than installing the new part. lol
Was this helpful?
Thank you for voting!
Element burned out
  • Francis E from Harwich, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Element burned out, ordered from Sears. Took over 2 weeks to get, originally sent wrong burner then shipped second one to wrong address. When I installed element I found that switch was also burned out . I ordered it from Parts Select & it was in the stove in 24 hours from the time I ordered it on line. Be assured I know where I will orde r my parts from now on
Was this helpful?
Thank you for voting!
Burner light was on all the time but burner was off.
  • Cliffford from Rochester, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Replaced the burner switch.
Was this helpful?
Thank you for voting!
Burner control failure/unable to regulate temp.
  • ROBERT from SALCHA, AK
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Unplug range from 220VAC outlet. Remove screws on back of range control panel and lift cover exposing controllers and wiring. Remove burner controller mount screws. Measure old controller shaft length/new controller shaft length (per instructions). Adjust new burner controller shaft length. Remove wiring from old controller (one at a time ) and place on new controller. Install new controller and secure with 2ea mount screws. Re-assemble cover/control panel. Plug range into 220VAC outlet. Have wife ops check....everyone's happy.
Was this helpful?
Thank you for voting!
burner would go red after a few mintes
  • richard from pottsville, AR
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
put it off a week before i worked on it but if you can replace a plug on a excord you can do this less than 5 mins
Was this helpful?
Thank you for voting!
The oven would not ignite
  • Richard from Boise, ID
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the bottom drawer, oven racks, and the oven floor panel. With a #2 cross tip screw driver, I removed the old igniter, replaced it with the new one and tested the unit. When the new igniter began to glow I turned the unit off and reassembled the oven - JOB DONE less than 15 minutes.
Was this helpful?
Thank you for voting!
Igniter in oven not working.
  • Rachel S from Dallas, GA
  • Easy
  • 15 - 30 mins
  • Nutdriver
Pulled racks and covers out of oven. Moved stove away from wall. removed bolts holding igniter. Disconnected wiring harness. Reverse process to install new part.
Was this helpful?
Thank you for voting!
Burner would go on and then turn off, repeatedly.
  • Robert from Tonawanda, NY
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Unplugged unit, removed plate behind control panel, removed 5 or 6 wire connectors, pulled off burner switch knob and removed 2 screws that holds switch in place. Reversed the procedure and was done.
Was this helpful?
Thank you for voting!
The large burner sometimes stayed on high too long, burning food
  • Harry from Seminole, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
My first approach was to try to find some help on the internet - Y-Tube or whatever. When I could not find anything, I was on my own. My first thought was that the best and easiest access to the switch was to somehow remove the top section of the range which held the switch. I was trying to avoid having to pull the range from the wall and cabinets. But not finding any way to do that, I then pulled the range from the wall, and removed the back panel (8 screws), which gave me easy access. Once that was done, the replacement went smoothly and quickly. So if replacing any switches on this range, FIRST pull it from the wall and THEN remove the back panel, and the rest is a piece of cake!
Was this helpful?
Thank you for voting!
Front large burner stayed on high
  • Lynn C from Leesburg, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
i personally did not do the repair..one of my neighbors did it and he said it was super easy..he pulled stove out from wall, unplugged it from socket, removed defective part, shortened clip that knob attaches to, installed new part with no problems whatsoever...plugged stove back in, pushed it back in place...burner now works fine! i was super impressed with the delivery of this part...ordered it on a Monday nite, it was mailed out the next day (Tuesday), and i received it Wednesday around noontime.. :)
Was this helpful?
Thank you for voting!
Burner goes full hot at any setting
  • Ronald from Clinton, TN
  • Easy
  • 15 - 30 mins
  • Screw drivers
First, I turned off the power at the switch box. Moved the stove out (That was a problem, because I am 80 years young) Removed the back panel, and moved the wires one at a time to the new switch. Removed the selector, then removed the 2 screws holding the switch in. Installed the new switch installed the dial selector, turned the power back on, and checked the burner. It works as advertised!!!!! Moved the stove back to its original position, and got a hug from my wife. PHEW!!! Now I think I'll take a nap.
Was this helpful?
Thank you for voting!
All Instructions for the 1028B
31 - 45 of 49