![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
Troubleshooting
This part works with the following products:
Range, Wall Oven.
This part works with the following products:
Frigidaire, Kenmore, Crosley, Electrolux.
Part# 316405000 replaces these:
AP3706691, 1056119, 316405001, 7316405001
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Miles K - April 4, 2021
Verified Purchase
Oven Door Seal
The part came fairly quickly and was super easy to install. My only negative comment would be the high cost of this part.
BOB T - September 15, 2020
Verified Purchase
Right part, right fast, right done.
Part exactly as described, arrived in a couple of days, easy to install.
Louis-François T - February 19, 2020
Verified Purchase
Great site
Very fast delivery
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 2.3 / 5.0, 1 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
My oven door seal was worn and did not seat properly. It leaked heat.The infinite burner was not warming in the low heat positions
I followed two very good videos on how to do the repairs. It took longer to clean all the disassembled parts and the glass than it did to actually do the repair.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to lock them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to lock them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.
Other Parts Used:
-
Frank from PALM COAST, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
May 14, 2019
I replaced the heat sensor and the oven still took 35 minutes to reach 350. I noticed that the range oven door seal is worm and torn at the bottom of the door. Can this cause the oven to loose heat and take so long to get to 350
For model number 79094462702
Hello Bob, Thank you for the question. Yes, if the seal is damaged or wore out it can cause the temperatures to be off since the hot air is not sealed. I suggest having it replaced to fix the issue. Hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
BINKHONG
February 17, 2023
Does installation requires the disassembly of the door or just pushing the ends of the gasket into the holes for the gasket?
For model number 97095164409
Hello Binkhong, thank you for your question. Yes, the door must be taken apart to install the Seal PS977704. We have a very good video for you watch on our website. We hope this information helps!
![](https://img.youtube.com/vi/5xO2vt8hIdI/maxresdefault.jpg)
2 people found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS977704
Manufacturer Part Number: 316405000
Manufacturer Part Number: 316405000
Brand
Model Number
Description
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)