The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or closed to the electronic control board. Before making this repair, you will want to make sure to unplug your microwave and discharge the capacitor. Your microwave capacitor is able to store electricity in large quantities even after it has been unplugged. The most common reason for replacing your relay switch is if the microwave will not turn on but your timer still runs..
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Steven S - January 24, 2021
Verified Purchase
It was the right part
Thanks. Everything went well. My microwave is up and running
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.1 / 5.0, 10 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Timer would run but the microwave won't start
I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up.
Other Parts Used:
Tim from Chicago, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
90 of 145 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave wouldn't turn on but timer worked.
was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a 12 volt battery and it was bad. Ordered a new one from Part select and got it fast . Works great .
Other Parts Used:
Steve from Moorhead, MN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
35 of 61 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave would count down but not run
After unplugging the unit remove the control face buy removing the screws. All three door switchs are on a bracket on the left. Remove the two screws holding the bracket in place and pull out. Disconnect the wires from the three switches and test each switch indivually to determine the bad one. I used a multimeter set on ohms.Replace the bad switch with the new one and replace all the wires. Reassemble the unit and you are good to go.
Other Parts Used:
Betty from Kimball, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
29 of 49 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave suddenly turned off and turntable would run with open door
replaced switch and capacitor also checked thermal fuse to make sure it was not defective
It is a undercabinet stovetop microwave. First had to take it down and unplug. Remove the top cover locate the door switch. Used neednose pliers to remove switch. Unplug two terminals.Plug new switch and use pliers to replace back @ same position.Plug in socket temporarily to see if it works.Afterwards if it works.Unplug and replace cover.Ready to be replaced back under cabinet.
Other Parts Used:
Danny from Yanceyville, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
24 of 39 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Everthing works except heating.
This is an OTR microwave oven, needs to be removed to diagnose problem. I did not diagnose problem properly, I searched online for possible causes, read that (99%)percent of the time the interlock switch was bad and replacement should solve my problem. It was also stated to be an easy fix,15- 45 minutes depending on ability. I ordered the relay switch. Took the oven down then removed outer shell. With my multimeter I began to test, fuses(2), interlock switches(3)and transformer. 3 interlock switches were ok, fuses were fine, and had power to the transformer, meter could not read output of transformer because of high voltage, (2300v). I'm down to magnetron (about a hundred bucks) or the touch pad/ circuit board. I have a countertop micro that I'm putting in place of the OTR. As far as Partselect, my item was shipped and delivered on time, instructions for changing that part was quite accurate. Would order from here again, just do my homework first.
Other Parts Used:
Michael from Waynesboro, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave Would Run And Count Down But Not Heat
Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.
Other Parts Used:
John from Selma, CA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench set
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer runs, but no heat.
I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.
Other Parts Used:
Joshua from Depoe Bay, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Instructions did not match the assembly of the ice maker.
I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply on my ice maker.
Other Parts Used:
Harry from Cypress, TX
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
0 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Power, light, and clock work, micro/turntable not working
Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch
Other Parts Used:
adam from new orleans, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
0 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
13 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tom
July 6, 2021
Is this the monitor switch?
For model number FGMV176NTDB
Hello Tom, Thank you for the question. This Switch is one of the Door Switches. This switch should be replaced is the appliance has power, timer counts down and the light comes on but will not start to heat or the tray will not turn. We hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Tom
January 17, 2022
When we open the door the fan is running. The microwave works but it seems wrong that the fan is like that. Would it be a switch? #PS8769124? Do you have a video of this fix? Thanks
For model number CPLMV169DCD
Hello Tom, Thank you for the question. There are three switches for this model. The Top and Bottom Switches are Part #: PS8769124 and the Middle Switch is Part #: PS2343189. We recommend testing each switch to see if they are reading Normally Open or Normally Closed. There will be markings on the switch to what it should read. We hope this helps!
Hello,
Microwave fan runs when the door is open. Otherwise, it works perfectly. Thank you for advising the part number to replace with instructions.
Regards.
For model number FGMV174KFB
Hello Mohideen, Thank you for your inquiry. We recommend checking the door switches first, there are 3 altogether and if one is faulty then it can cause the fan to come on when the door is open. You can test the switches with a multimeter. For safety reasons, since the microwave capacitor can still store electricity even when the microwave is unplugged, it is usually advised that you discharge the capacitor before any attempt at repair. We have included a link on how to do so.
https://www.partselect.com/Microwave+discharge-capacitor+repair.htm
Good luck with your repair.
I have a similar issue (no heat in microwave) to that from Robby listed in the questions (August 30, 2022) so I bought item #FRG5304493153 (PartSelect Number PS8769124) which your website claims to be the appropriate repair fix 99% of the time this "no heat" issue occurs in the model number for my microwave. Unfortunately, the order relay switch does not match the label indicated on the relay switch in my microwave oven and it didn't work when installed and shorted the electrical panel (note: my relay switch is labelled D3V-1G-2C25 with a red button - if that matters- and a 0.1A250VAC rating whereas the ordered piece appears to have a different rating labelled "16A-1/2HP-125 OR 250/VAC" and an orange button).
Note: I'm aware that there are also two identical other switches linked to the door latch (D3V-16G-3C25) which I have not touched.
I don't see any other relay switches so I don't think the ordered piece works with my microwave.
Would you have suggestions on how to repair this "no heat" issue (e.g., do you sell the relay switch that's in my microwave)?
For model number CPLMZ209GCA
Hi Craig, thank you for reaching out. The door switch listed under your model is part number PS8769124. For the no heat issue, we would suggest checking the following parts: rectifier assembly, part number PS2343253, and magnetron, part number PS1148111. However, for the shorted electric panel, we would recommend replacing it. The part number is PS979641. We hope this helps!
Hello Michael, thank you for your question. Before you begin, unplug your microwave. Then remove the screws securing the vent in place with a Philips screwdriver. You can use a putty knife to help pry off the vent. Unscrew the screws for the control assembly. Lift up the control panel to detach. Take a picture of how the wires are installed. Disconnect the wires and remove the panel. Take a picture of the door switches before removing them. To remove them, pry them off with a flathead screwdriver. Remove the screws holding the door switch holder to the frame. Lift the switch holder up and remove it from the frame. Use a small flathead screwdriver to press the tab to remove the center door switch. Install the new door switch by snapping it into place in the holder. Insert the switch holder back into the frame and secure it with the screws. Note the pictures you took to reinstall the wires. We hope this helps. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Michel
July 19, 2023
how do you discharge the high voltage capacitor
For model number cplmz209gca
Hello Michel, thank you for your query. A capacitor is discharged by creating a short circuit between each of the two capacitor terminals, and between each terminal and the chassis. The chassis is the metal mounting or the bare metal surface of the capacitor. With your microwave unit unplugged, touch the blade of a well-insulated screwdriver to one terminal. Gently slide the screwdriver forward until it reaches the other terminal, holding it there for a few seconds. Be aware that this often results in a loud and startling noise. Repeat this procedure in order to create a short circuit between each capacitor terminal and the chassis or the bare metal mounting plate surface. Good luck with your repair!
Was this helpful?
Thank you for voting!
Julian
September 8, 2023
Latch on door stays open
For model number GLEB27M9FBD
Hi Julian, thank you for the great question. We would recommend you change the door lock latch motor and switch assembly, part number PS5574140, to help fix this issue. Glad to be of assistance!
What part do I need if there is no power coming out of the microwave? I have plugged it in other working sockets and no luck.
For model number FPMO209KFP
Hi Jesse, thank you for reaching out. We have concluded that the issue is with the thermal fuse, part number PS466969, which may need to be replaced. We hope this solves your problem!
Switch PS8769124 came loose from bracket. I popped it back into place. Now microwave turns on as soon as door is closed.
For model number FPMC2785KFB
Hi Peter, thanks for reaching out to us! Our research indicates that this could be an issue with the switch itself, or the bracket it is attached to. If they are out of alignment, they could be miscommunicating with the board. If you are looking to purchase this part then you can do so by either adding it to your cart and going through the checkout process online, or by calling our customer service line and ordering with one of our agents. I hope that helps. Good luck with your repair.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Affresh® Dishwasher Cleaner is the #1 recommended cleaner by Whirlpool, KitchenAid, and Maytag brands, designed to remove limescale and mineral build-up that can affect your dishwasher’s performance. These powerful table...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS8769124
Manufacturer Part Number: 5304493153
