Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Overfill then no fill
Remove bottom kick plate and raise the feet up. Remove attachment from the top to counter. Slide out. Facing the unit, remove left hand side sheet metal cover. The unit is behind this cover. Unhook the hose on the lower end. Pop the new one in and hook it up!! Test on quick rinse and see results. If ok return to normal as disassembled. Make sure to level the unit after tucking it back in. Enjoy!!
Other Parts Used:
Lawrence from FREDERICKSBRG, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
December 6, 2019
Bosch dishwasher just hums after starting, i assume this the drain pump i'm hearing?, and does not continue ie: No water fill and no washing. Replaced water inlet but after a few washes, same thing. Replaced water fill control valve, washed once and same thing. I have discovered that banging my fist on the interior of the dishwasher in the neighborhood of the control valve and then starting....works! there is no water in the overflow tray, dry as a bone. can't figure why it is stuck in drain mode, or whatever the humming noise might be, and does not begin a cycle without me pounding on it.
For model number SHU43C07UC14
Hello Gary, Thank you for the question. This sounds like an issue with the Control Unit in the panel, PartSelect Number PS8730628. It could be a lose wire or a defective board. Hope this helps!
Hi Larry,
Thank you for your inquiry. Yes, the switches are included with the pressure chamber. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Scot
May 5, 2018
I winterize the dishwasher by disconnecting the water supply, adding antifreeze into the washer basin, pressing two buttons together to force discharge. Maybe i need to add a step to open the solenoid and allow water to drain out of backwards thru open solenoid. This spring i am not able to get water into the basin, i see no leaks. I question if solenoid is not actuating, or water fill sensor assembly area would be the issue.Suggestions? Troubleshooting sequence? Thanks.
For model number SHU43C02UC14
Hi Scot,
Thank you for your question. If the dishwasher will not fill with water, there are some parts that you will need to check to see which ones are causing the issue. You will need to check the water inlet valve and the float switch. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Matthew
December 2, 2019
Does this part include the gasket?
For model number SHU3305Uc/U12
Hello Matthew, thank you for your question. It is sold separately, as Sealing part number PS8697074. Good luck with your repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
