![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
Product Description
Clutch Lining Kit Specifications
This kit comes with springs, hardware, and brake lining.
![How Buying OEM Parts Can Save You Time and Money How Buying OEM Parts Can Save You Time and Money](https://img.youtube.com/vi/d6AvOkulk_g/maxresdefault.jpg)
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Spins slowly | Will not agitate
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Whirlpool, Kenmore, KitchenAid, Roper.
Part# 285790 replaces these:
AP3094538, 2690, 285790, 285141, 285332, 285381, 285421, 285538, 285759, 3354731, 3354732, 387712, 388190, 3946793, 3951308, 62698, 62705, 63047, 63175, 63766
...
Show more
, 64177, 64194, W10817174, W10817385
Show less
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Robbi H - September 24, 2021
Verified Purchase
easy repsir
Came fast, fit perfectly, my 20 year old washer is working great.
Peter J - June 4, 2019
Verified Purchase
Great service from Part Select!
These folks had the best prices and parts came in no time. Their site also lots of great DYI videos to do repairs with their parts. I've already referred them to friends who are experiencing washer problems.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 2.5 / 5.0, 7 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Agitator had a terrible ratcheting sound when running in free-wheel mode during spin cycle.
Removed the gearbox from the drum and removed the direct drive motor from the gearbox. Disassembled gearbox and drained gear oil. Rebuilt the neutral drive assembly with the ordered parts. Cleaned sealing surfaces. Filled gearbox with new gear oil. Sealed and re-installed the top cover to the gearbox. Reattached motor and then reinstalled assembly to drum and clutch (installed new clutch lining at this time as well).
Other Parts Used:
-
Adam from Lehi, UT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
96 of 121 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spin cycle stopped working
Farly easy repair, once I figured out the problem. The clutch assebly plastic part broke (over 15 yrs old), which is the part that engages the drum for the spin cycle. Following the very helpful diagram on Part Select, I removed the agitator cap and bolt from inside the agitator assembly, and pulled the assembly out of the drum. Then I put the washer on its side and removed the three bolts and two hose claps that hold the motor assembly. I pulled the motor assembly along with the drive shaft out to access the clutch/brake assembly area, removed the broken plastic drive piece and re-assembled.
Other Parts Used:
-
Brent from Highlands Ranch, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
40 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.
Other Parts Used:
-
Kevin from Disputanta, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
15 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washmachine wouldn't spindry
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.
Other Parts Used:
-
Chuck from South Holland, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
14 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump but not spin-oil leaking-agitation noise
Replaced AGITATOR DIRECTIONAL COGS (4) looking instruction video . Replaced CLUTCH LINING KIT following video of this site "WASHER REPAIR-REPLACING THE CLUTCH ASSEMBLY". Replaced SEAL, GEARCASE COVER and NEUTRAL DRIVE ASSEMBLY as follow: 1)CLUTCH Assembly and motor removed, took the GEARCASE on a bench vise to hold in place and the long shaft up side. You can get help from other person to hold secured in place instead a vise.2)Following a youtube video I tested gearcase with a reversible drill using DIRECT DRIVE MOTOR COUPLING PART next To transmission side instead of electrical motor. Drill turning counter clockwise drive the long shaft oscillating (it agitate via agitator cogs). Drill turning clockwise run the exterior sleeved part around shaft (upper side of metal gear inside gearcase and fixed on top to clutch to get washer spin). My experience was didn't rotate so we had to take apart gearcase cover.3)Unscrewed and removed gearcase cover. Cover was sticked by old seal gasket so a screwdriver helped me to remove it.4)Cleaned joint removing old gasket.5)Repeating drill test I realized big nylon gear did'nt rotated and removed uppercut clip with pin pliers with care for not lose the pin. Removed the next washer, the plastic gear and found a plastic part with a tooth broken. This part is with NEUTRAL DRAIN ASSEMBLY so replaced assembly following part instructions. I recommend take pictures in order to reassemling and use ALLEN WRENCH 5/32'' inches.6)Fill up to half of gearcase with 16 ounces (about 1/2 of case) of gear oil supplied by PARTSELECT or automotive gear oil SAE 85w90 or SAE 90.7)Replaced SEAL, GEARCASE COVER. HARD TO REMOVED AND REPLACE! Take care not break!. I had to use a piece of metal tube and a vise.8)Applied automotrice black seal gasket silicone around the cover joint and case.9) Replaced the cover and reversal instruction video.THANKS to this site I get excellent service and Enjoyed with my toy.
Other Parts Used:
-
Alvaro from CLEMENTON, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spin cycle was not working / poor
Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.
Other Parts Used:
-
Craig from Plano, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wouldnt agitate or spinn but would drain?
So i replaced the above parts pulled gearbox put new oil in all looked good but when i tryed it filled started spinning for a few sec.then quit again?was makeing a clicking sound so i layed on the floor and the drive coupling was spinning so i took the water pump off and it started agitating and spinning. found about a 6 in.thin piece of wire in it, dont know where it came from but installed a new pump and it works like a new one !!!
Other Parts Used:
-
lester from Belleville, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Blair
February 4, 2019
I have a washer that spins but not fast enough to spin all the water out of the clothes i looked at the motor coupler and found no cracks thanks for your help
For model number tawb600pqo
Hello Blair, Thank you for contacting us. If the motor coupling appeared to be in working order, I suggest checking the following parts: PS334641 Clutch Assembly, and PS11741239 Direct Drive Water Pump. Good luck with your repair!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Rusty Stafford
March 6, 2019
Washer won’t spin on high spin cycle on normal wash but if you turn dial to casual wash and start spin only by hand, it will spin.
For model number LSQ9950PW2
Hello Rusty, thank you for your question. We would recommend checking the Clutch Assembly
Part Number: 285785, and the Direct Drive Motor Coupling Part Number: 285753A. These are the two most common causes of spinning issues. I hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Guy
September 8, 2017
My washing machine makes a loud clicking noise while operating. It sounds like if a spring was releasing hard, i found what looked like a clutch assembly under the tub and would love to talk with someone about this.
For model number 11020702290
Hi Guy,
Thank you for contacting us. It sounds like you need to replace the direct drive motor coupling, part number PS1485646, that is between the transmission and the motor. It is made up of 2 plastic parts with one on the transmission and one on the motor. There is a black rubber isolator between the couplers that is probably worn and you may need to replace it. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Adrian
January 22, 2020
Hi, the washer is having a spin issues. It starts to spin and seconds into the spin there is a very loud bang and the basket jerks to a stop. About a minute later this repeats until the timer finishes the cycle.Any help is appreciated.
For model number 11024962300
Hello Adrian, thank you for your question. That issue is most likely caused by the clutch, but we would recommend testing or checking the following parts. Direct Drive Motor Coupling Part Number: 285753A, Drive Block - 2 5/16" High Part Number: WP389140, Clutch Assembly Part Number: WP8299642. I hope this helps.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS334642
Manufacturer Part Number: 285790
Manufacturer Part Number: 285790
Brand
Model Number
Description
Kenmore
10682872600
Washer
- Kenmore Washing Machine Model 106.82872600 (10682872600, 106 82872600) Parts
Kenmore
1101050299
Washer
- Kenmore Washing Machine Model 110.1050299 (1101050299, 110 1050299) Parts
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)