Real ratings from other people who bought this part.
Average Rating:
★★★★★
★★★★★
3 Reviews
4.7
Out of 5
5 Stars
2
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
Search reviews left by others. DIY doesn't mean you have to do it alone. Use simple keywords like "fit", "broken", "easy", or "quality" to find reviews that match!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Peter H - March 24, 2024
Verified Purchase
Functions like the original
Easy to install. Took only a few minutes
★★★★★
★★★★★
Clint M - March 9, 2024
Verified Purchase
Easy repair!
Although not the correct part for my ancient stove, this fit perfectly and works very well. The original was rectangular in shape, unlike this one. This produces better distributed heating.
★★★★★
★★★★★
Michael S - May 28, 2025
Verified Purchase
Quick delivery
The part arrived much faster than expected. I must admit I was surprised it was in good condition because it travelled in an empty box with nothing to prevent it from bouncing around, not even some crumpled paper!
Unfortunately while my repair was pretty easy, my oven is still not working - turns out the control panel may have also suffered in the malfunction.
Prev
1
Next
Repair Tips
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
Easy
15 - 30 mins
Average repair rating from 40 real customers like you
Sort by:
Prev
1
2
3
Next
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sorry, we couldn't find any existing installation instruction that matched.
bake element shorted out, sparking like a sparkler
89 of 99 peoplefound this instruction helpful.
Carl from Wynnewood, PA
Really Easy
Less than 15 mins
Nutdriver
first, made sure circuit breaker was off second, used nut driver to remove 2 screws on old element, pulled it from the back of the oven third, removed 2 wires from old element (spade connectors) fourth, connected new element and pushed back into oven. fifth, reinstalled 2 screws securing new element
this was
... Read more all done by my 15 yr old son under my supervision.
Read less
Was this helpful?
Thank you for voting!
bake element burned itself out ( as a welding rod does with all the fireworks)
21 of 25 peoplefound this instruction helpful.
joseph from ferrisburg, VT
Really Easy
30 - 60 mins
Nutdriver, Socket set
removed 4 screws of the back fan cover, then removed the two screws holding the element and disconnected the slip-on electrical wire connections. replaced enement and cover in reverse. this was all done after i cut power at circut breaker duhh
Was this helpful?
Thank you for voting!
Bake Element Burned Through A Weak Section Of The Tube.
18 of 19 peoplefound this instruction helpful.
PAUL from CAMDEN, AR
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
I removed the two mounting screws then pulled the element forward and disconnected the two element screws. I reversed the process to install the new one/ this oven is over 30yrs old.
Was this helpful?
Thank you for voting!
Baking element broke in half
12 of 12 peoplefound this instruction helpful.
Nancy from West Harrison, IN
Really Easy
Less than 15 mins
Wrench set
I removed the screws holding the old element in place, then pulled it out a few inches from the back oven wall. Then I pulled the wires away from the old baking element (pulled off easily), and being careful to keep the wires on the same sides as before, pushed the new element on to the wires. It was then just a matter of inserting the
... Read morewires and insulation back into the opening and tightening the screws. Simple!
Read less
Was this helpful?
Thank you for voting!
the bottom baking element broke on my upper oven... cracken in half
9 of 11 peoplefound this instruction helpful.
Kathy from Naperville, IL
Easy
Less than 15 mins
Pliers, Wrench set
It was very simple.. first turn off the electricity... next take out the two screws holding the element to the back of the oven... then pull the two plugs apart( male and female ends) ... throw away old part. put new part in by plugging the male and female ends back together... push back into oven back.. get all insulation back in...
... Read more put two old screws back in to secure... done.. turn on power... don't be afraid.. it was very, very easy.
Read less
Was this helpful?
Thank you for voting!
Lower element burned out
7 of 7 peoplefound this instruction helpful.
John from Germantown, WI
A Bit Difficult
15 - 30 mins
Screw drivers
Remove the screws inside the oven holding the back of the element to the rear wall of the oven. These scrrews are a square drive. Pull element forward and remove 2 screws that hold wires in place. Both sets of screws needed to be replaced with a different size. Reverse order to install.
Was this helpful?
Thank you for voting!
Oven bake element blew out
6 of 6 peoplefound this instruction helpful.
Michael from Indianapolis, IN
Really Easy
Less than 15 mins
Pliers
Shut off the power from the fuse box. Removed p the two screws and plate that attach the element to the wires and back of oven. Installed the replacement element by attaching the wires and reinserting the two screws. Restored power and tested the new element by preheating the oven at 350 degrees and letting it heat for 15 minutes. Works
... Read more like a charm!
Read less
Was this helpful?
Thank you for voting!
26 year old oven, lower element burned into two pieces.
6 of 6 peoplefound this instruction helpful.
marsha from oklahoma city, OK
A Bit Difficult
1- 2 hours
Nutdriver, Screw drivers
I first removed the broken element by removing the two hexhead screws on either side of the element bracket. Then I gently pulled the wires through the opening and removed two more screws that attached the wiring to the element. I then compared the new and old elements and found a few differences.
First, the screw holes whe
... Read morere the wires connect to the element were tiny in the new element, about a third the size of the holes in the old one. Secondly, the mounting bracket was not as long as the original, and the holes to mount it to the back of the oven are located at the top of the bracket, instead of the sides.
Since this was the only element that I have found, that comes close to the original, I decided to make it work.
I took my drill and a small bit and bored out the screw holes, just enough to get a self taping screw to fit and reconnected the wires.
Now I'm not sure that I would recomment the next step to anyone, but I did this: I held the new bracket against the back of the oven and drilled new holes to match the new bracket, and again used self tapping screws. The reason that I don't encourage this is that the new bracket fits just inside of the old opening, but the insulation cannot be seen as long as the element does not get moved. I then plugged the original bracket holes with the original hex head screws.
It took a little more time and effort than I had expected, but well worth it, after eight months without the use of my oven.
Read less
Was this helpful?
Thank you for voting!
Baking element quit
4 of 4 peoplefound this instruction helpful.
Richard from Laguna Niguel, CA
Very Difficult
More than 2 hours
Nutdriver, Pliers, Socket set, Wrench (Adjustable), Wrench set
Removed burned out element and discovered replacement element had a different back plate and different hole pattern. Also, the electical connecttion from power wires to ends of element were a TOTALLY different size, both in hole size and size of material that hole was placed. This tood a lot of slow increasing the size of the hole time.
... Read more Also, the backplate was a different size with a two hole pattern at the top of the plate, as oppossed to the original plate with holes centered at the sides of the plate. Had to drill holes in back oven wall higher than I wanted, as the oven wall had a depression in the back wall and I could not drill at that point. By drilling holes that were higher than previous holes, there was now a 1/2" opening at the bottom of this plate. Used a hack saw and cut off a piece of the old plate to slip underneath, then screwed in the new plate, thus filling the remaining opening, and securing the additional hand made additional plate. This was a lot more than I had bargain for, and when I turned on the oven, it did not work! I re-checked the connection of the power wires to the grid element and found one of the connections to be disconnected. Reconnected this wire and everything is just ducky now.
Read less
Was this helpful?
Thank you for voting!
Bad element
3 of 3 peoplefound this instruction helpful.
Ed from Talladega, AL
A Bit Difficult
15 - 30 mins
Nutdriver, Pliers
Removed mounting screws and element only pulled out about 2 inches. Disconnected wires and had to drill slightly bigger hole in element ends to reattach wires. Element mounting bracket was different than old element. Had to use one existing screw hole in oven back and drill a new one.
Was this helpful?
Thank you for voting!
Prev
1
2
3
Next
DIY Questions and Expert Answers
28 questions answered by our Repair Experts.
Ask our experts a question about this part and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pat - For model number JKP15WW1WW
September 21, 2017
Will this heating element fit my appliance?
Hi Pat,
Thank you for your question. Yes, this is actually the correct part for your model information. GE has removed the 0 between your Ws. Good luck with your repair.
11 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Audrae - For model number JRP24GOV1BB
February 26, 2020
Will this part be the correct size for my old oven? I need the heating element. It burned up during self cleaning.
Hello Audrae, thank you for your question. The bake element for this unit (lower element) is PartSelect Number: PS249249. This will fit your unit. Good luck with your repair!
5 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Judy - For model number JRS04
October 5, 2023
What are the measurements of this element?
Hi Judy, thank you for contacting us. The approximate dimensions of this heating element are:
13.5 inches width, 15.75 inches length from mounting bracket to the end of the element, 2.875 inches length from bracket to the terminal end, 1.75 inches mounting holes center to center. We hope this information helps!
3 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Michael - For model number JMP31W0W2WW
April 2, 2019
Want to make sure that this is the correct bake element for my oven.
Hello Michael, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS8688123. Thank you for your inquiry, good luck with this repair!
3 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Ellen - For model number 9114042593
October 16, 2019
Looking for top broiler model # above. Serial # 5g573811q
Hello Ellen, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS249244. Hope this helps!
Need baking heating element for this GE wall oven. In your search there is no "0" after the "g" does this matter
Hi Joe, thank you for your question. Yes, that would be correct. You no longer need that 0 in your model number. So this element would be the correct part for your model. I hope that helps. Good luck with your repair.
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
David - For model number JRP14G0P4BG
September 9, 2021
My baking heat unit has gone out and will not heat. What baking heat unit will be a good replacement for my GE built in electric oven?
Hello David, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS249424. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Could the elements be the problem if the oven doesn't heat up enough? My oven reads 350 but temperature reads 220.
Hello Jeanne, Thank you for the question. I Suggest testing the Oven Sensor, PartSelect Number PS236043. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Thank you for your inquiry, good luck with this repair!
Hello Carol and thanks for writing.
If the oven temperature is higher than the level set, then most likely the thermostat needs replacement. Heating elements: The oven can also overheat if there is a malfunction with its heating element. ... A problem with the sensor can cause the oven to overheat. We hope this helps. Please contact us anytime
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
John - For model number 6790-688031
December 28, 2019
What are the dimensions of this part and does it have smallish slide on connectors to the stove - part wb44k5013
Hi John, we cannot find parts based on part dimensions as even parts that are the same size can have small differences that make them incompatible with your model. However if you could supply your model number we would be happy to research the correct parts for you. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
Prev
1
2
3
Next
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Item is in stock and is estimated to be delivered in 2-3 business days via Standard Shipping.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Element or Burner","title":"Element or Burner","url":"/Wall-Oven-Elements-and-Burners.htm"},{"position":2,"name":"WB44K5013","title":"WB44K5013","url":""}]
My Orders
