This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking | No hot or cold water
This part works with the following products:
Washer.
This part works with the following products:
General Electric.
Part# WH13X10027 replaces these:
AP3995139, 1264511
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 6 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water was very slow filling and relay hummed loudly.
Disconnected electrical power plug and two water inlet hoses Removed three screws holding control panel to back panel. Slid control panel sideways then tilted forward to expose inlet valve. Removed the two clip wiring connections and two hold down screws. Compressed the spring clip on the outlet hose and slid it off the valve. Installed the new valve in reverse order. Reinstalled the control panel and three attachment screws. Reconnected the water hoses and plugged the electrical cord back in. Started wash cycle to check out. It now fills properly. Problem solved!!
Other Parts Used:
John from Mt. Pleasant, SC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
32 of 34 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water keeps running into machine even after it finished the cycle.
Removed the old part put it in the trash, installed the new part. Very easy repair to make.
Other Parts Used:
Don from Dahlonega, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
17 of 20 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
there was no water filling the tub.
unpluged the machine.undo the hoses off the machine took the back plate off to were I could access the triple water inlet took off the two wiring adators,and the hose that was on the triple water inlet then the two phillipshead screws. throw the bad one in the trash.and then put everything back together
Disconnected the water lines. Removed three screws to remove cover. Removed the two screws holding the water inlet valve and disconnected the power source. Then reconnected the new valve. Process only took twenty minutes.
Other Parts Used:
Noah from LIMA, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tom
January 13, 2018
My machine seems to run fine. The only problem is that there is that the water always continues to drip. It never shuts off completely. I have to turn off the water shut off to stop it from dripping. After the spin dry, if i don't turn off the water the clothes get soaked again. What do you think is wrong?
For model number S3700G0WW
Hi Tom,
Thank you for your question. It sounds like your water inlet valve needs to be replaced. You can test it with a multi meter before hand to see if it is working correctly, but it seems like perhaps one of the solenoids are stuck open and that is why you are getting that constant dripping. I hope that helps. Good luck with your repair.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Thayne
February 22, 2018
Water keeps running (does not fill,goes out drain for over 30 minutes). I unplugged the washer, and water does not run. Will water inlet valve fix my problem?
For model number WJRR4170G1WW
Hello Thayne, thank you for your question. Yes, If the water is not coming into the unit, I would recommend replacing the water inlet valve part number WH13X10027.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Pat
November 18, 2017
Draws full water for wash but draws only 2 slow streams for on right and left of water stream for rinse. Works fine for wash, very, very slow drawing for rinse.
For model number WBSR3140G1WW
Hello Pat,
Thanks for your question. Your water valve may have a plugged up screen or the line may have low pressure.
Remove the cold water fill hose, put the hose in a bucket and check the water pressure.
If the pressure is fine, check inside the valve where the water line attaches to. If the screen is dirty, clean it and reattach the hose. Otherwise, you may wish to consider replacing the valve.
I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Virgil
January 9, 2020
Hot water will not fill. Only small trickle. Checked inlet hose and filter. Both ok. Will triple water inlet valve fix this problem
For model number WJSR4169GOWW
Hello Virgil, thank you for your question. Yes, the most likely issue is a bad water valve. We would recommend replacing that part to fix the issue. I hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Our scratch-free, streak-free formula removes fingerprints, smudges, grease, dirt and oil, while protecting and polishing to repel dust and dirt. Use on all stainless steel appliance brands and surfaces. Stainless Steel ...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1482391
Manufacturer Part Number: WH13X10027