Spark Ignition Valve Switch
Fits your 629CG200!
$69.94
In Stock
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your 629CG200!
PartSelect Number
PS11757574
Manufacturer Part Number
WPY704512
Manufactured by
Whirlpool
Product Description
Spark Ignition Valve Switch Specifications
This spark ignition valve switch is an inch and a half long. It is a white switch with a black cam. Sold individually.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start
This part works with the following products:
Cooktop.
This part works with the following products:
Jenn-Air, Kenmore, Whirlpool, Maytag.
Part# WPY704512 replaces these:
AP6024223, 4381623, 7-4512, 704512, 7403P916-60, Y704512
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The right rear burner ignition switch malfunctioned.
Repair is simple as long as you TURN OFF THE CIRCUIT BREAKER first. After that, take off the cover over the switches (pull knobs off, remove 2 screws and lift off the cover), pull the bad switch straight up off the gas valve, pull the two wires off the switch, plug them back onto the new switch, place it back over the gas valve stem, reassimble the cover and knobs, turn back on the circuit breaker, and verify that ignition switch works. Not a hard repair. (HINT: while you are waiting on the replacement part, you can light the bad burner by turning on the opposite burner ignition switch and using that "spark" to light the other burner.)
Other Parts Used:
-
Max from Plano, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
19 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter stuck in on position.
removed 2 screws to access the ignitor. Discinnected the wires from the old ignitor and slid the old ignitor off. Installed the new ignitor and attached wires.
Other Parts Used:
-
terry from joplin, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One burner would not ignite (no spark)
Since the other three burners sparked, I traced the problem to the switch on the valve shaft. To replace, (after unplugging the power cord) I pulled off the knobs, removed the two screws on the valve cover (inside the downdraft vent) and pulled the switch up the shaft to remove. I transferred the spade terminals to the replacement switch, oriented and installed.
Other Parts Used:
-
Mark from Clarksburg, NJ
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Back right burner would not ignite. Bad Switch
I removed the burner knobs, unscrewed the 2 screws and removed the cover. I pulled the old switch off the stem and removed the wires. I reconnected the wires to the new switch and pushed it in place on the stem. After checking to make sure the new igniter switch worked, I replaced cover tightened the 2 screws and replaced the knobs. Job done in 5 minutes!
Other Parts Used:
-
Phliip from Scituate, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Veronique
May 8, 2019
The top left burner sparks at intermediate time.What part do i need to replace?
For model number CG205W
Hi Veronique,
Thank you for your question. A normally functioning igniter will typically click up to three times before it sparks. But, every now and then you may run into instances where the ignitor continues to click or tick even after the burner is lit, or the burner never lights at all. A clicking ignitor typically is not dangerous and may continue to click if the gas is shut off.
One of the most common sources of this issue is that the Burner Cap is out of place. Make sure the cooktop is completely cooled and remove the Burner Grate to access the cap. Try removing the cap and center it on the base. If the burner cap is askew, it can prevent the burner from lighting.
If that doesn’t work, check for moisture. If you recently had a pot boil over on burner, a food or grease spill, or cleaned the cooktop, there may still be moisture present even if it looks dry. Remove the burner cap and give the burner time to air dry. To speed up the process, make sure all the burners are off and towel off the top of the range. You can then either use a fan aimed at the range top or set your oven to 350° and leave it on for around 30 minutes to speed up dry time.
If you see that there is debris stuck in the holes in the burner, that could also potentially be the culprit.
You can use a metal pin or paper clip to clear the debris out of the grooves. Never use items such as toothpicks to do this, they may break off and get lodged inside.
If you get through all of these tips and still have the clicking problem, it may be the Spark Module and the Spark Ignition Switch. You can find replacements for your model stove for purchase on our website. If you feel comfortable, this is a repair you can do yourself. But, if you’re ever unsure don’t hesitate to contact a technician and consult your owner’s manual. I hope this helps. Thank you and have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11757574
Manufacturer Part Number: WPY704512
Manufacturer Part Number: WPY704512
Brand
Model Number
Description