Maytag/Maytag_Thumb/36206.gif
See part 15 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.ca

JUMPER WIR

★★★★★
★★★★★
1 Review
$11.72   In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11757520
Manufacturer Part Number WPY304693
Manufactured by Whirlpool
Troubleshooting
This part fixes the following symptoms:
No heat or not enough heat
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Maytag.
Part# WPY304693 replaces these:
AP6024170, 303708, 304693, Y303708, Y304693
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories
 Average Repair Rating: 3.2 / 5.0, 6 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Maytag DE512 dryer would't heat.
After 22 years of continued use, my Maytag dryer stopped heating. Needless to say that I'm very impressed with the quality of Maytag products and I haven't had any problems with this unit until now. Your website was very informative and it really helped me pinpoint my problem. The parts were easy to install and it took less then 1 hour to complete. First: disconnect the power cord and the vent hose and lay the dryer on its back. There are two screws on the bottom of the door frame, remove these and then tilt the door assembly up until you can unlock the spring clips which hold the top of the door assembly to the dryer frame. Disconnect the two wires that are attached to the door switch and remove the door. The heater element is located on the right side, it's tube shaped. Remove the two slip-on connector wires attached to the top of the heater element. There are 4 tiny screws (use nut driver) holding the heater assy. First, remove two screws that hold the metal flap on the front of the element tube, then remove the screw located inside the element near the front lip (use a short nut driver) and then one screw attached to a flange at the back-end of the element on the right side. Pull out the heater assy, and install the replacement. If you're replacing the short jumper wire located on the element so be sure to replace it before you install the new element. Bolt the new element to the dryer using the 4 tiny screws, connect the 2 wires to the heater assy, re-attach the door by first aligning the spring clips to the top of dryer assy, then re-connect the 2 wires to the door switch, lower the door assy and install the 2 screws at the bottom of the door frame. Re-connect the vent hose and power.
Other Parts Used:
Complete Heater and Housing Assembly - 240V
  • Jim from Bethlehem, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
43 of 50 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grounded heat element
Took front off dryer. Unwired heating element and removed. Installed new heat element and wired with wires. Dryer is cherry!!!!!!!!!!!!!!!!
Other Parts Used:
Complete Heater and Housing Assembly - 240V
  • Steven from Franklin, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
heating element and lead failed
very straight forward job.I removed the front panel,unhooked the wires,removed and replaced and the heating element.
Other Parts Used:
Complete Heater and Housing Assembly - 240V
  • Don from Mediapolis, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench set
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer runs but no heat.
I went ahead and replaced all the thermostats, heater assembly and jump wire which was very easy after watching the installation videos. The new heater assembly was a little tough to get to fit in. but managed to get it to fit. Turned it on but to my surprise no heat. Someone earlier had told me that a friend had the same problem and it was a faulty circuit breaker but I didn't think that could of been the problem. I then checked it and sure enough that is what was the problem, it was only get power on one leg of the breaker. Put in a new circuit breaker and every thing works great. I don't mind putting in the new parts at least I have a piece of mind that that it's in good shape and have back up spare parts if needed.
Other Parts Used:
Cycling Thermostat (Limit: 140-20) Cycling Thermostat - L150-25F Complete Heater and Housing Assembly - 240V High Limit Thermostat (Limit: 200-30)
  • BRIAN from ALMA, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer overheating.
Per your video
Other Parts Used:
Complete Heater and Housing Assembly - 240V High Limit Thermostat (Limit: 200-30)
  • Joe from MARYVILLE, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heater Element broke
Took the front cover off and remove three screws and took the heater Element housing out. Removed four screws opened the housing removed two screws, the took out the old Element , put in the new one. Replaced all screws and the front cover. Turned the power on and hit the start button and it works perfectly?.
Other Parts Used:
Heater Element - 240V
  • Steven from Sanford, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11757520
Manufacturer Part Number: WPY304693
Brand
Model Number
Description
Maytag
BDE7500
Dryer - Residential
Maytag
DE106
Dryer - Electric
Maytag
DE107
Dryer - Electric
Maytag
DE110
Dryer - Electric
Maytag
DE18CA
Dryer - Electric
Maytag
DE18CM
Dryer - Electric
Maytag
DE18CT
Dryer - Electric
Maytag
DE19CA
Dryer - Electric
Maytag
DE19CD
Dryer - Electric
Maytag
DE19CS
Dryer - Electric
Maytag
DE19CT
Dryer - Electric
Maytag
DE210
Dryer - Electric
Maytag
DE212
Dryer - Residential
Maytag
DE21CA
Dryer - Electric
Maytag
DE21CM
Dryer - Electric
Maytag
DE21CS
Dryer - Electric
Maytag
DE21CT
Dryer - Electric
Maytag
DE22CA
Dryer - Electric
Maytag
DE22CS
Dryer - Electric
Maytag
DE22CT
Dryer - Electric
Maytag
DE23CD
Dryer - Electric
Maytag
DE24CA
Dryer - Electric
Maytag
DE24CM
Dryer - Electric
Maytag
DE24CS
Dryer - Electric
Maytag
DE24CT
Dryer - Electric
Maytag
DE25CS
Dryer - Electric
Maytag
DE26CA
Dryer - Commercial
Maytag
DE26CD
Dryer - Commercial
Maytag
DE26CS
Dryer - Electric
Maytag
DE26CT
Dryer - Commercial

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service