Maytag/Maytag_Thumb/47406.gif
See part 19 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.ca

Light Bulb - 120v 25w

$48.89   Special Order

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11747808
Manufacturer Part Number WPA3167501
Manufactured by Whirlpool
Product Description

Light Bulb - 120v 25w Specifications

Sold individually.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Dryer, Microwave, Microwave Oven Combo, Vacuum.
This part works with the following products:
Amana, Magic Chef, Norge, Kenmore.
Part# WPA3167501 replaces these:
0068901, 0087273, 0090395, 01060008, 01060018, 01060024, 01060028, 14202454, 202479, 21608, 25T8DC, 30283-A, 3387683, 3392120, 520224, 53-0177, 53-0570, 661555, 701247, 790170 ... Show more , A0278301, A0352501, A3167501, C0436401, WX12X1560, Y0068901, Y0087273, Y0090395, Y01060008, Y01060018, Y01060024, Y01060028, Y520224, Y701247, Y90395 Show less
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories
 Average Repair Rating: 3.3 / 5.0, 7 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    Dryer made a loud noise and vibrated badly
    First I made sure the unit was unplugged. I popped the top of the unit with a slotted screw driver, lifted the top up and rested it against the wall behind the dryer. I removed the two screws - one on each side in front on top of the dryer cabinet. Then I tipped back the front panel of the dryer slightly with the door of the dryer closed. I unclipped the door switch with a slotted screw driver and then lifted the entire front panel including the door off of the the two floor clips on bottom. I set the front panel aside. Next I lifted the large drum slightly to dislodge the rollers in back and slid the drum back slowly while sliding the thin belt back on the drum until the drum was out of the unit and the belt was detached and loose. Then I cleaned the unit thoroughly, vacuumed all lint and dirt and wiped down the outside of the large drum with mineral spirits to make sure it was totally clean and smooth. Then I removed the two rollers and the roller shafts at the back of the unit following the directions enclosed. My slip-ring pliers came in handy to remove the retaining rings on the roller shafts. I replaced the rollers and roller shafts and the supplied washers and spacers as per the instructions. I sprayed a little WD-40 on the surface of the rollers and it stopped all squeaking and vibration of the drum. Next I replaced the front drum pads and runners as per the instructions. I then slid the drum back in place taking care to slide the new belt back around the drum in the same position as the old belt. Now came the difficult part - laying on the floor and reaching under the drum I positioned the belt around the motor shaft and tension pulley. This must be done by "feel" and must be done correctly!! Follow the instructions on the positioning of the belt very carefully and make sure it is in the correct position on the drum, motor shaft, and tension pulley! Next, get up and rock the drum up and down slightly to make sure it has engaged the two rear rollers properly. Rotate the drum manually one or two turns to make sure the belt is in the correct position. Then replace the front door panel by dropping it onto the two clips at the base of the unit and taking care to replace the door switch in reverse order of taking it out. Then replace the two screws at the top front on each side of the unit to secure the front panel. Lower the top of the unit back in place, plug in the dryer, turn it on and enjoy the lack of noise you have created.
    Other Parts Used:
    Rear Drum Support Roller Kit Front Glide Kit Multi Rib Belt - 92-1/4"
    • Thomas from Oneonta, NY
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Nutdriver, Pliers, Screw drivers
    62 of 71 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Light Bulb
    Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!
    Other Parts Used:
    • Terri from Kingsland, TX
    • Difficulty Level:
      Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Screw drivers
    6 of 11 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    burnt out lightbulb for over 20 years
    Unscrewed back plate, and replaced bulb
    Other Parts Used:
    • Kathtleen from Bristol, CT
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Screw drivers
    3 of 3 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Light bulb went out in mictowave
    Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.
    Other Parts Used:
    • Linda from BURSON, CA
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      Less than 15 mins
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Microwave oven bulb had burned out
    My Dearest One removed the screws that held the part that covers the bulb; removed the old bulb, put in the new bulb and replaced the cover.
    The whole operation took less than 5 mins.
    Thank you.
    Other Parts Used:
    • Deidre from Brownsville, TX
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Screw drivers
    1 of 2 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Light Noise
    Its good to clean all the lint out the the dryer and vents on a yearly bases as to many years of lint build up can catch on fire and make a mess . Replacing the glides was easy . Make sure you clean all the old glue , so the pads stay in place as there need to compensate for minor frame to drum differences .
    Other Parts Used:
    Dryer Drum Glide - Left Side Dryer Drum Glide - right side Right Side Drum Glide Pad
    • Mark from Howard Lake, MN
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      More than 2 hours
    • Tools:
      Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
    1 of 3 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Dryer would not run.
    First you need to raise the top in order to get to the parts. Then the door is removed, I did this in order to thouroughly clean the lint build up in the duct work. Then the high limit thermostat is removed in the back top part of the dryer, just above the heater. Then the heating element is removed by removing one long screw that holds the heater and the fused thermostat. Once all these parts are removed and the wires disconnected you simply reverse the process with the new parts. Put it all back together and everything works fine. Part Select.com also was helpful in diagnosing the cause of the problem. Thanks.
    Other Parts Used:
    High Limit Kit
    • James from Owings, MD
    • Difficulty Level:
      Easy
    • Total Repair Time:
      15 - 30 mins
    • Tools:
      Nutdriver, Pliers, Screw drivers
    0 of 1 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS11747808
      Manufacturer Part Number: WPA3167501
      Brand
      Model Number
      Description
      Kenmore
      10687884100
      Dryer
      Kenmore
      10687884300
      Dryer
      Kenmore
      10687884600
      Dryer
      Kenmore
      11086884100
      Washer Dryer Combo
      Kenmore
      11086884300
      Washer Dryer Combo
      Kenmore
      11086884600
      Washer Dryer Combo
      Kenmore
      11086884700
      Washer Dryer Combo
      Kenmore
      11086884800
      Washer Dryer Combo
      Kenmore
      11086894100
      Dryer
      Kenmore
      11086894300
      Dryer
      Kenmore
      11086894500
      Dryer
      Kenmore
      11086894700
      Dryer
      Kenmore
      11086894800
      Dryer
      Kenmore
      11086982100
      Dryer
      Kenmore
      11086982110
      Dryer
      Kenmore
      11086982300
      Dryer
      Kenmore
      11086982310
      Dryer
      Kenmore
      11086982700
      Dryer
      Kenmore
      11086982710
      Dryer
      Kenmore
      11086982800
      Dryer
      Kenmore
      11086982810
      Dryer
      Kenmore
      11086983100
      Dryer
      Kenmore
      11086983110
      Dryer
      Kenmore
      11086983130
      Dryer
      Kenmore
      11086983300
      Dryer
      Kenmore
      11086983310
      Dryer
      Kenmore
      11086983700
      Dryer
      Kenmore
      11086983710
      Dryer
      Kenmore
      11086983800
      Dryer
      Kenmore
      11086983810
      Dryer

      Get in touch, we're here to help!

      Open until 1am EST

      Contact Customer Service