Whirlpool WP9760774 - Element, Broil | PartSelect.ca
Our response to COVID-19
We're open and continuing to ship packages. Learn about our response to COVID-19
Element, Broil – Part Number: WP9760774
Element, Broil – Part Number: WP9760774 https://partselectca.azureedge.net/Schematics/Whirlpool/2GGFKMJN.gif

Element, Broil

12 Reviews

Your Price

CAD$130.45

PartSelect Number PS11747304
Manufacturer Part Number WP9760774
Manufactured by Whirlpool

This broil element is found on the roof of the oven. The broil element is at the top of the oven and supplies the heat to broiling. 14" x 15" with 1-3/8" inserts. This part works with the following brands: Whirlpool, Roper, Admiral, Maytag, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric.

This part works with the following brands: KitchenAid, Crosley, General Electric, Maytag.

This part works with the following products: Range, Wall Oven, Microwave Oven Combo.

This part fixes the following symptoms: Little to no heat when broiling | Element will not heat | Little to no heat when baking | Oven not heating evenly

Videos For installing this part.

Questions & Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Customer Repair Stories

Average Repair Rating: 3.9 / 5.0, 8 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
David from Catonsville, MD
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench set
Parts Used:
WP9760774
The broiler element in my wall oven burned out
This was easy and I'm glad I didn't go to the trouble and expense of hiring an appliance repair person. I'm reasonably handy, but I really have no experience in this kind of repair. I'd like to mention that the part I ordered arrived in just two days and it was exactly the right part, so I was very pleased in that regard.

After turning off the circuit to the wall oven and confirming that the power was off, I had to remove the oven from the wall in order to access the wires and connections in the back. Normally, this wouldn't have been necessary because usually the broiler element can be disconnected from the clasps that connect it to the electric source by simply unscrewing the defective element from the roof of the oven, pulling gently on the connection ends from inside the oven cavity in order to "pull out" an inch or two of the electric source wires and the metal clasps that accept the "male" connecting ends of the broiler element. Once the a bit of the wire and the metal connecting clasps are exposed and able to be held with pliers, the element can be disconnected from the connector clasps by simply pulling on the prongs of the element (hard).

But in my case, one of the metal connecting clasp for one of the wires had melted, presumably when the element burned out, and that clasp could only be accessed and replaced from the back of the oven. Also, I would imagine that the wires and clasps could "slip" back behind the unit when they're disconnected if that's not done carefully. However, removing the wall oven was pretty easy for me -- even as a one-person job. I just put a tall table in front of it and slid it out so that it rested on the table.

If you have to replace a metal connector clasp, they're inexpensive and available in the electrical departments of hardware/home stores.

In my case, there's a metal panel at the back of the oven that had to be unscrewed and removed so that I could access the areas where the electrical source wires connect through the back wall of the oven to the broiler element. This was just a matter of removing a few screws and then removing the metal panel.

Once the metal panel at the back of the oven was removed, I was able to replace the melted connection clasp by using a wire cutter/stripper and then pliers to secure the clasp on the end of the exposed wired by deforming the clamp with the pliers. Once that was done, I simply removed the screws that held the broiler element to the top of the oven cavity, disconnected the remaining three clasps that connect the element to the source wires (the fourth clasp was the one that had melted and that I'd replaced), removed the defective element, inserted the four "male" prongs of the broiler into the four clasps that connect them to the source wires, replaced the metal panel at the back of the oven, screwed the new element back into the top of the oven, slid the oven back into the wall cavity, turned the circuit back on, crossed my fingers, and everything worked like a charm.

I saved a money, but more importantly (for me) I saved a lot of time that I would have had to have spent waiting around for a repair person.
21 of 22 people found this instruction helpful.
Was this instruction helpful to you?
James from Dublin, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP9760774, WP4449154
Broiler element not working
Removed back of oven. Disconnected 2 connectors on each side of element. Removed screws that were too rusted to use screwdriver with vise grips. Removed old element, inserted new element through holes in rear of oven.Installed 1 screw on each side of element in rear and 2 screws in front where brackets support the front of the element.Put back panel back on. Push oven back in place, plug back in outlet.It works great and I didn't have to pay service man.
9 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Salle from Marietta, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WP9760774
broiler element broke into
There were 4 screws to remove and 2 wires to disconnect. We placed the order on line for replacement. It arrived the next day. We simply installed the new element by connecting the 2 wires (very easy) and putting the 4 screws back in place. It works like new and was sooo easy.
7 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Stephen from HOUSTON, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
WPW10131825, WP9760774
Broil element burned out/temp sensor questonable
I followed instructions from the videos provided on the Part Select site. As with many such appliances, parts are interchangeable between brands. this unit is a KitchenAid but Whirpool,Kenmore parts interchange...Access from the front is all that's needed however and the only tool required was a phllips head screw driver...the only negative surprise (which the video warned about but I ignored) was the risk of the element leads drawing back through the holes, which 2 did. Save yourself that trouble by securing the wires to the back oven wall with a small strip of duct tape until you're ready to re-attach them to the new element. This necessitated removing the oven entirely for access to the back; the most time consuming aspect being removing/replacing what seemed like 20 odd screws holding the back cover in place! If not for that mistake, entire job would have been under 30 minutes. Well worth the effort and would do it again!
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Patrick from SANTA CLARA, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Parts Used:
WP9760774
Smaller broiler coil stopped working.
Our double-oven is wall-mounted, so accessing the backside to change the wires (as shown in the instruction video) was not a practical do-it-yourself option. After turning off the circuit breaker and disconnecting the broken broiler element, it is pretty easy to pull the four connection wires through the backside of the oven, which allowed us to disconnect the slide clips. We attached twist-ties to each clip/wire before disconnecting to keep the clips/wires from pulling back behind the oven wall when moving the new element into position. We found it necessary to crimp a few clips onto the new element to make secure connections, but the rest of the project went pretty much as shown in the video and the new element works great.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Ronald from DAVIS, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Parts Used:
WP9760774
Center broiler element burned out
Removed oven door for easy access. Removed 4 phillip head screws that held broiler element from top of oven. pulled wires a couple of inches out from back of oven and used flat screw driver to help separate the wires connecting the broiler from the oven. Did the opposite to install the new element,.
The best part of this operation was the fact that the part arrived from Part Select by Fed X the next day after ordering it all for a shipping cost of $8.75. Great Service Highly recommend Part Select.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Michael from ARLINGTON HTS, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Parts Used:
WP9760774
Heat element needed replacing
Repair was really simple. Saw that the outer shielding on the existing heat element had degraded and ordered a new element. Part was shipped to my house in two days. Actually took me longer to get the oven door off than to replace the element because the left bracket on the door was slightly bent. Element came out after removing 4 screws and disconnecting 4 wire terminals. I was able to do the repair inside the oven and did not have to pull it away from the wall as the wires were long enough to pull through. I used some painter's tape to tape down the disconnected wires so they would not fall back behind the oven. Then I used a needle-nosed pliers to slightly crimp the wire terminal to the heat element and screwed in the four screws. That was it! Never did this type of repair before and it was really easy. Also estimate that for my 20-25 minutes of work I probably saved over $200 in parts and labor if I hired someone to do it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Richard from EUGENE, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP9760774
Replace Broiler Element on a slide in range
Using the video from PartSelect I followed the steps shown. Sliding the range out was difficult so I tilted it forward resting the frame on a 5 gallon plastic bucket. I did have to crimp on a new terminal. The repair was straightforward.
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
12 Reviews
5
out of 5
Filter By Rating:
  • 5 Stars
    12
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Model Cross Reference

Brand
Model Number
Description
Crosley
CT15G4Q
Refrigerator
KitchenAid
KDRS807SSS00
Range
KitchenAid
KDRS807SSS01
Range
KitchenAid
KDRS807SSS02
Range
KitchenAid
KDRS807SSS03
Range
KitchenAid
KDRS807SSS04
Range
KitchenAid
KDRS807SSS05
Range
KitchenAid
KDRS807XSP00
Range
KitchenAid
KDRS807XSP01
Range
KitchenAid
KDSS907SSS00
Range
KitchenAid
KDSS907SSS01
Range
KitchenAid
KDSS907SSS02
Range
KitchenAid
KDSS907SSS03
Range
KitchenAid
KDSS907SSS04
Range
KitchenAid
KDSS907SSS05
Range
KitchenAid
KDSS907XSP00
Range
KitchenAid
KDSS907XSP01
Range
KitchenAid
KEBC167MSS00
Wall Oven
KitchenAid
KEBC167MSS01
Wall Oven
KitchenAid
KEBC167MSS02
Wall Oven
KitchenAid
KEBC167MSS03
Wall Oven
KitchenAid
KEBC167MSS04
Wall Oven
KitchenAid
KEBC167VSS00
Wall Oven
KitchenAid
KEBC167VSS01
Wall Oven
KitchenAid
KEBC167VSS02
Wall Oven
KitchenAid
KEBK101SBL00
Wall Oven
KitchenAid
KEBK101SBL02
Wall Oven
KitchenAid
KEBK101SBL04
Wall Oven
KitchenAid
KEBK101SSS00
Wall Oven
KitchenAid
KEBK101SSS02
Wall Oven