Part Location Diagram of WP8066018 Whirlpool Spring, Lid
See part 10 in the diagram
Replacing your Whirlpool Dishwasher Spring, Lid
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Spring, Lid

★★★★★
★★★★★
13 Reviews
$10.11
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11744874
Manufacturer Part Number WP8066018
Manufactured by Whirlpool
Product Description

Spring, Lid Specifications

This metallic spring is for your dishwasher's soap cup cover. Sold individually.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Whirlpool Dishwasher Spring, Lid

Replacing your Whirlpool Dishwasher Spring, Lid
Troubleshooting
This part fixes the following symptoms:
Will not dispense detergent | Door latch failure | Not cleaning dishes properly | Door won’t close
This part works with the following products:
Dishwasher.
This part works with the following products:
Whirlpool, Kenmore, Roper, Estate.
Part# WP8066018 replaces these:
AP6011676, 300106, 8066018, 99989653
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
13 Reviews
4.5
Filter By Rating:
  • 5 Stars
    10
  • 4 Stars
    2
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    1
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
Customer Repair Stories
 Average Repair Rating: 4.0 / 5.0, 12 reviews. What's this?
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Worn out spring on detergent release box lid
First, examine very carefully how the old spring relates to the detergent release box lid. Note that the top of the spring has a square-end upside down "U" . This rests on a small ledge on the detergent box. Also note that on either end of the spring is a straight extension of the spring wire. These two "legs" must rest on the inside of the edge of the detergent box. Second, use a flat blade screw driver to pry the LID hinge pin from the mounting "posts. Remove the pin, first noting the position of the spring. Reassemble the spring on the hinge pin in reverse order. Then snap the lid onto the spring using the two mounting "posts". NOTE: I used a very fine needle nose pliers to move the two spring "legs" behind the detergent box edge after I had mounted the lid. Flip the lid down to test if the spring pressure on the lid can be felt. Harold Kitzmann, Fishersville VA
Other Parts Used:
Pin (Lid Hinge)
  • HAROLD from FISHERSVILLE, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
86 of 101 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
soap dispenser door/spring broken
removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.
Other Parts Used:
Soap Dispenser Cover Dishwasher Door Gasket - Gray Pin (Lid Hinge) Door Vent Screen
  • KEVIN from PLAINFIELD, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
30 of 54 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
soap lid missing
Replacing the pin with the spring is a little tricky, it was hard to hold it. And the little plastic pin breaks real easy too, its hard to get the lid to snap in place without breaking the pin.
Other Parts Used:
Wheel Assembly Soap Dispenser Cover Rinse Aid Cap Pin (Lid Hinge)
  • Jim from Oktaha, OK
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
8 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
soap dish door does not always pop open
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Other Parts Used:
  • John from Dubuque, IA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
7 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the pin was broken
but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door
Other Parts Used:
Pin (Lid Hinge)
  • Jo-Anne from Columbia, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inserting Lid Spring
Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.
Other Parts Used:
Soap Dispenser Cover Pin (Lid Hinge)
  • Emile from Jamaica, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No water to the upper rack, soap dish not opening properly
Replaced the middle spray arm kit and the upper spray arm mount. Also replaced worn out spring for the soap dish.
Now all areas of the dishwasher get cleaned and the soap dispenses correctly every time.
Other Parts Used:
Upper Spray Arm Mount Middle Spray Arm Kit
  • Dan from NEWPORT, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Soap Lid Pin Broken
Snap the old lid off, remove the pin & spring & install new Pin & Spring. Very easy. Thanks To Parts Select got the right parts.
Other Parts Used:
Soap Dispenser Cover Pin (Lid Hinge)
  • Robert from Port Clinton, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
4 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The spring on the detergenet dispenser box door failed and needed replaced
The old spring on the detergent dispenser box door failed and the dispenser door would not pop open at the right time in the wash cycle.

Ordering the new spring was easy on the website. Need dishwasher model number, stock number and serial number.

Hint - Order at least 2 springs! They are not expensive.

I followed the instructions in the video. I could get the spring on the spindle correctly but could not get the two spring prongs to catch to create spring tension on the door without using a thin knife blade to carefully push each prong to where it caught on the dispenser door.

I needed to slide the prongs slowly and carefully to get them to catch on the door. This distorted the spring. That's why you really need two springs. I then used needle nose pliers to pull the latching part of the spring to catch on the inner door. That distorts the spring, too.

So you really need two springs. One spring to learn how to do it and a second one to replace the one you distorted as you learned.

Take care
Other Parts Used:
  • John from WESTERVILLE, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
SOAP DISPENSER DOOR DID NOT CLOSE.
WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.
Other Parts Used:
Soap Dispenser Cover Pin (Lid Hinge)
  • ROBERT from MAHWAH, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ling
January 22, 2023
The soap dispenser sometimes has soap left after washing and dishes are not clean. A few times the door of dispenser is not open. Which parts should I replace? Thanks!
For model number 63013003016
PartSelect logo
Hello Ling, Thank you for your inquiry. If the dispenser is not opening and releasing the soap, then check the parts of the dispenser such as the seal, the spring and the lid. The seal is only available as part of the complete dispenser assembly. It could also be caused by the water not being hot enough so we would recommend checking the water circulation pump with heater and make sure that the water going into the dishwasher is hot. You can test the pump with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps.

Was this helpful?
Thank you for voting!
Related Parts:
Alvin
May 31, 2023
Soap dispenser doesn’t open during cycle But when I manually turn the knob through each cycle it opens.
For model number DU810SWPU3
PartSelect logo
Hi Alvin, thank you for contacting us. The issue probably seems to be with the dispenser actuator assembly, part number PS392727. It opens the dispenser cover to release detergent and rinse aid during the dishwashing cycle. If you require assistance to place an order, please contact customer service!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11744874
Manufacturer Part Number: WP8066018
Brand
Model Number
Description
Kenmore
110723120
Dishwasher
Kenmore
110773811
Dishwasher
Kenmore
110773812
Dishwasher
Kenmore
110773813
Dishwasher
Kenmore
110773881
Dishwasher
Kenmore
110773882
Dishwasher
Kenmore
110773883
Dishwasher
Kenmore
19385
Dishwasher - Kenmore Dishwasher Model 19385 (1988) (19385(1988)) Parts
Kenmore
19585
Dishwasher - Kenmore Dishwasher Model 19585 (1988) (19585(1988)) Parts
Kenmore
19985
Dishwasher - Kenmore Dishwasher Model 19985 (1988) (19985(1988)) Parts
Kenmore
5648600110
Refrigerator - KENMORE REFRIGERATOR
Kenmore
5648600140
Refrigerator - KENMORE REFRIGERATOR
Kenmore
5648600160
Refrigerator - KENMORE REFRIGERATOR
Kenmore
5648600180
Refrigerator - KENMORE REFRIGERATOR
Maytag
601W
Washer Dryer Combo - Residential
Maytag
60W
Washer Dryer Combo - Residential
Maytag
61W
Washer Dryer Combo - Residential
Kenmore
65715755791
Dishwasher - Kenmore Dishwasher Model 657.15755791 (65715755791, 657 15755791) Parts
Kenmore
66513402K900
Dishwasher
Kenmore
66513402K901
Dishwasher
Kenmore
66513409K900
Dishwasher
Kenmore
66513409K901
Dishwasher
Kenmore
66513442K900
Dishwasher
Kenmore
66513442K901
Dishwasher
Kenmore
66513443K900
Dishwasher
Kenmore
66513443K901
Dishwasher
Kenmore
66513444K900
Dishwasher
Kenmore
66513444K901
Dishwasher
Kenmore
66513449K900
Dishwasher
Kenmore
66513449K901
Dishwasher
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service