Average Repair Rating: 4.4 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The cold water would not shut off. (many diff. error codes)
1. Unplug the machine. Take off the cold water line from the machine. 2. Take out the two screws from top back to remove top. 3. Unplug the three electrical connectios from the valve sylenoids. 4. Take off the two screws that hold the three way valve to the machine back. 5. Unclamp the three clamps and remove the hoses from the valve end. 6. Place the hoses and clamps on the new valve. 7. Reincert the three electrical connectioins. 8. Secure valve in place with the two screws from above step 4. 9. Replace top and secure with two screws from step 2. 10. Connect cold water line. Plug machine in. 11. Done.
PS. There is a diagram of the connections on top of the distribution center.
Other Parts Used:
James from Promont, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
31 of 40 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Because of sand in my well water,the valve quit working properly and water would run constantly
I removed two screws on the back of the washer,removed the top of the washer unclipped three plastic wiring clips, removed two screws holding the valve in place.replaced valve and replaced wires and top of washer. Total time about 15 minutes
Other Parts Used:
Robert from Monticello, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
9 of 11 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Marie Swenson
September 5, 2017
My washer won't disperse the fabric softener. It will do the soap and the bleach. Is the cold water inlet the problem. Or what else should i check.
For model number MAH9700AWW
Hello Marie, thank you for contacting us. There can be three reasons why fabric softener does not drain. Make sure the washer is leveled. If the washer is not even, residual of fabric softener can be collected in your washer and clog the dispenser. Make sure the dispenser is not clogged. Remove the dispenser and then remove the blue siphoning cap. Rinse the dispenser thoroughly in warm water and then reinstall the cap and dispenser. Check the inlet hose screens for a blockage. If your washer is not getting enough water pressure, the fabric softener will not drain. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Steve
March 4, 2018
The washer has error code nf would replacing the inlet valve fix this?
For model number MAH8700AWW
Hi Steve, Thank you for the question. NF means "no flow". Check for proper water pressure from the house.If water pressure is good, check the water valve inlet screens for debris. Check the fill hoses for blockages as well. If everything is clear the valve will need to be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ron
November 14, 2019
Both the pre-wash and bleach water valves vibrate when operated. The cold water and hot water valves don't. Will replacing the 3 way water valve fix this?
For model number MAH8700AWW
Hello Ron, Thank you for the question. Sounds like the valve PartSelect Number PS11741549 is not opening properly and they should be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
This part is the replacement hot water valve for your washer. It is approximately 2-1/2 inches by 3-1/2 inches, and the valve head is approximately 1 inch in diameter. The hot water inlet valve in your washer connects t...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11741549
Manufacturer Part Number: WP34001248
