Product Description
Lid Switch Specifications
The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Maytag Washer Lid Switch
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Will not agitate | Will not drain
This part works with the following products:
Washer.
This part works with the following products:
Maytag.
Part# WP22003804 replaces these:
AP6024324, 22003804
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Jason H - November 4, 2021
Verified Purchase
Easy Repair Great part.
Great part worked perfectly. Amazing next day delivery.
Jerry D - December 10, 2019
Verified Purchase
Part worked great - easy fix!
Following videos the fix was extremely easy. Anyone can do it!
Pierre G - August 20, 2018
Verified Purchase
Easy to replace and work as expected!
Fast shipping. Thanks.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 3 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washing machine shut off at begining of cycle
The washing machine was full of clothes, water, and detergent when it decided to stop working. I pulled the washer away from the wall (I recommend using two people for this), and removed the back access panel (two screws at the top and bottom). With the washer plugged into the wall outlet I used a multimeter to test electrical distribution through the system. Power goes directly to the Lid Switch from the outlet and is disrtibuted to the washer from this point. When I physically engaged the Lid Switch power was not distributed to the system. This told me that the switch was bad. I unplugged the washer from the wall outlet, then removed the Lid Switch.
To remove the Lid Switch, disconnect the wire connection by pulling straight up, pull back then up on the Lid Switch and it should slide out.
Keep in mind when this happened it was 8 or 9 pm, no supply depots open. I don't recommend an amateur performing this, but in order for me to get the clothes washed I made a jumper wire, composed of two wires twisted together at one end, (wires need to be of equal or greater gauge). I inserted the twisted end of the jumper wire into the black wire port of the Lid Switch wiring connector, then inserted one of the wires into the red wire port and one into the yellow wire port of the connector. Making sure the jumper wire did not make contact between the red and yellow, I plugged in the washer. The washer completed the cycle.
Installing the Lid Switch, reverse removal.
To remove the Lid Switch, disconnect the wire connection by pulling straight up, pull back then up on the Lid Switch and it should slide out.
Keep in mind when this happened it was 8 or 9 pm, no supply depots open. I don't recommend an amateur performing this, but in order for me to get the clothes washed I made a jumper wire, composed of two wires twisted together at one end, (wires need to be of equal or greater gauge). I inserted the twisted end of the jumper wire into the black wire port of the Lid Switch wiring connector, then inserted one of the wires into the red wire port and one into the yellow wire port of the connector. Making sure the jumper wire did not make contact between the red and yellow, I plugged in the washer. The washer completed the cycle.
Installing the Lid Switch, reverse removal.
Other Parts Used:
-
Jason from Aberdeen, MD
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
97 of 117 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had placed clothes, water and detergent in machine but it did not start the cycle.
I am a woman (small) very low on funds and could not see myself spending $140 plus parts. I found your website and was able to determine the cause of the problem, since it did not appear the solution would be too difficult to accomplish I ordered the two parts that could be causing the problem. The parts were delivered in 2 days and I was able to do the repair in less than 15 mins I only used the lid switch. The old parts do just snap out and you snap the new one in. Thank you so much for your site. In these economic times you are a godsend.
Keep up the great work and again thank you!
Keep up the great work and again thank you!
Other Parts Used:
-
Ines from West Babylon, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
43 of 55 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid switch was broken when the lid slammed shut
The installation was extremely easy - videos sure helped. I would recommend this site for appliance parts - parts came ahead of schedule.
Other Parts Used:
-
Gary from Evans, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rita Poe
August 25, 2017
Does this part come with the plastic part that attaches right to the lid of the machine?
For model number MAV6457AWW
Hi Rita,
Thank you for the question. The part on the lid is called the Cam and is sold separately from the lid switch.
Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Ronald
January 17, 2019
Will part number wp22003804 work on this model Maytag wash machine
For model number MAV6650AWW
Hi Ronald,
Thank you for your question. Yes, this lid switch is listed under your model number and it will work with your appliance. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11739463
Manufacturer Part Number: WP22003804
Manufacturer Part Number: WP22003804
Brand
Model Number
Description