This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: This is a redesigned part. The pump now mounts on to the b...
Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY availab...
This is a replacement lid switch actuating cam for your washer. The cam is located on the underside of the washer lid, near the hinge. The cam actuates the lid switch, so your washer knows the lid is ...
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This part is the replacement motor pivot spring for your washer. It is made of metal and is approximately 3 inches long and 2 inches wide. The motor pivot spring helps hold the drive motor in the corr...
$12.45
On Order
Questions And Answers for MAV6457AWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rosa
August 10, 2021
What is the load capacity on this washer?
For model number MAV6457AWW
Hello Rosa, Thank you for the question. This model is 3.3 Cubic Feet. We hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Monica
December 28, 2019
I'd like to know the capacity of this washer , how many pounds ?
For model number MAV6457AWW
Hi Monica, there is no exact lbs capacity for this model, the manual does state capacity based on water level setting for example on super setting you can have the drum up to 3/4ths full. The manual is on this page under Manuals & Care Guides and this information is on page 3. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
Susan
December 29, 2021
My washer won't do anything no water.
For model number MAV6457AWW
Hi Susan,
Thank you for your question. If your washer will not fill with water, there are some parts that you will need to check to see which one is causing the issue. You will need to check the water inlet valve, the hose washers and screens, the lid switch, the lid switch actuating cam and the drain pump. We have included a link that you may reference on how check these parts. We hope this helps! Good luck with the repair!
My washer stopped spinning the clothes. How do I fix this?
For model number MAV6457AWW
Hi Ken, thank you for reaching out. Based on our research, we would recommend checking the thrust bearing kit, part number PS2003651. It includes the pulley that rotates to spin the basket and the thrust bearing that fits between the pulley and the transmission shaft. You may need to replace it to fix the issue. We hope that helps!
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do.
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed. Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.