Spring Retaining Clip WP22001650

Official part for Maytag, Amana, Speed Queen, Whirlpool

Easy 

1- 2 hours 

11739294-1-M-Whirlpool-WP22001650-Spring Retaining Clip
Part Location Diagram of WP22001650 Whirlpool Spring Retaining Clip
See part 27 in the diagram
( Grid squares measure 1x1 inch )
11739294-1-S-Whirlpool-WP22001650-Spring Retaining Clip 11739294-2-S-Whirlpool-WP22001650-Spring Retaining Clip 11739294-3-S-Whirlpool-WP22001650-Spring Retaining Clip Part Location Diagram of WP22001650 Whirlpool Spring Retaining Clip
Proudly Canadian
OEM badge Official OEM Part
$15.40
In Stock

Part Fit Check - Make Sure it's a Match.

Where to find your model number

About This Part

What it does. Why it matters. Everything you need to know for an easy fix.

Spring Retaining Clip Specifications

This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.
Part #WP22001650
Manufactured by Whirlpool for Maytag, Amana, Speed Queen, Whirlpool

You May Also Need

Because heroes deserve fewer surprise re-installs.

$50.55
In Stock
$26.85
Special Order
$34.95
In Stock
$29.95
In Stock
$35.15
In Stock
$35.95
In Stock
$35.15
In Stock

Genuine OEM: Original Parts. Lasting Repairs.

Because quality isn't optional.

OEM stands for Original Equipment Manufacturer. This means that the company who made your appliance is also supplying the replacement part.

How Buying OEM Parts Can Save You Time and Money
Features OEM Generic
Genuine brand name
Guaranteed to fit
Superior Quality
Long term value

About this fix

Common problems and models this part fixes.

Easy 

1- 2 hours 

Rated by verified customers

Works with the following products:
  • Dryer
  • Washer
  • Washer Dryer Combo
Part# WP22001650 replaces these:
AP6006227, 2-12982, 212982, 22001650, 28835, 56080, R0601520

Repair Tips

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!

Easy 

1- 2 hours 

Average repair rating from 8 real customers like you

Sort by:
  • 1

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sorry, we couldn't find any existing installation instruction that matched.
unusually loud rumbling in spin mode, no spin out
37 of 45 people found this instruction helpful.
  • Ralph from Moreno Valley, CA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
removed outer enclosure to expose inside workings. removed all retaining springs to tub and transmission housing. Inverted tub to access agitator pulley and belt. Removed pulley and cut belt off.(I knew I was replacing it, anyway.)Had to remove large tub bracket to exchange new pulley for old. Disconnect bleach reservoir filler tubing on tub assembly. Disconnect power connector to drive motor. Removed water pump to access drive pulley where new belt belongs. Aligned belt to pulleys and checked idler pulley tension which was acceptable. Replace helix drive lug against spin/agitator and tightened retaining bolt. Assembled components in reverse order and conducted test run. Success. Smooth running machine and saved about $200 on professional labor costs. I had no repair manual but you should have a personal confidence in general repair work. Something like a history of taking things apart and putting them back together successfully. I had an independent appliance repair guy examine the washer and he said it was too complicated for him. Once I had it apart, it seemed fairly basic. Good luck!
Read less
Was this helpful?
Thank you for voting!
Agitator action was slow/weak; Bleach tube kinked
25 of 37 people found this instruction helpful.
  • Robert from Marlboro, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
UNPLUG THE MACHINE FIRST!
a) Remove the front panel (use a putty knife to release clips)
b) Fashion a small hook-end out of a coat hanger
c) Install an additional glide spring (2 + 1 = 3) to get extra retraction of vee-belt around drive pulley as follows.
d) Hook end of of the new spring onto rear (back) hole of moving motor mount (observe orientation of existing springs to be sure that you're hooking up spring into hole correctly).
e) Lie on your right side, hold the spring in place with your left hand (go around back of the motor with your left hand).
f) Have someone hold the flashlight as you take a coat hanger and fish for the front end of the spring under the motor glide.
g) With front - end of spring held by coat hanger hook, pull spring towards you and slip spring into front hole of stationary motor mount.
h) Lightly spray in and around glide area with Teflon non-stick dry lube (DuPont or Liquid Wrench dri-lube product line).
Machine agitates like-new now.
Bleach Tube:
a) Remove hose clamps at both ends using a screwdriver.
b) Remove and discard old tube.
c) Slip on the hose clamps and slicker-up the ends of new tube with palmolive liquid detergent and slip onto tub and bleach dispenser.
d)Tighten clamps.
Read less
Was this helpful?
Thank you for voting!
Many problems
8 of 19 people found this instruction helpful.
  • Deanna from Fort Lauderdale, FL
  • Difficult
  • More than 2 hours
  • Screw drivers, Wrench set
It would seem that my unhappy washer decided to
have a multiple component breakdown. after replacing one part after another, my baby runs like new. parts arrived quickly and installed easily, it was all the diagnostic that took the most time. the forums were quite helpful.
Was this helpful?
Thank you for voting!
Tub gasket leaking because of age.
2 of 2 people found this instruction helpful.
  • Donald from GROSSE PT PK, MI
  • Really Easy
  • 1- 2 hours
  • Screw drivers, Wrench set
Top came off quickly with socket wrench. Removed gasket in about a minute. Spent 45 minutes getting grime ( soap and lime) off of top. Took five minutes to replace gasket.

Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.
Read less
Was this helpful?
Thank you for voting!
Water leak at bottom of tub, leaking onto floor.
2 of 3 people found this instruction helpful.
  • Brian from Allentown, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.
Read less
Was this helpful?
Thank you for voting!
30 year old washer started to leak on left side
1 of 2 people found this instruction helpful.
  • Richard from Ridgefield, CT
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench set
Noticed small pool of water on left side. Diagnosed it was injector tube. Ordered parts.

Removed front panel by removing two phillips screws and then pushed down to disengage spring clips.

Used nutdriver to remover two bolts holding top cover and then undid bleach dispenser hose.

Lifted top cover and removed clamps holding injector and fill. Replaced using 1 1/16" Stainless steel screw clamps.

THIS WAS THE FIRST REPAIR EVER ON THIS WASHER!! SIMPLY AMAZING PERFORMANCE. STILL SPINS AT HIGH RPM AND IS QUIET. Bought for my folks as a gift in 1979.

This is the reason I bought the last Maytag top loaders made in '05. Also had another one 24 years with only one repair.

Parts Select, thank you! Parts arrived in three days.
Read less
Was this helpful?
Thank you for voting!
Dryer was making a loud screeching noise
1 of 3 people found this instruction helpful.
  • Andy from York, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Once I determined where the noise was coming from I took the front cover off, two screws at the bottom and clipped at the top. Then I removed the lint screen shroud . Instructions said to remove belt and drum, but I was able to pull the drum forward enough to get to the roller without removing the belt. I removed the snap ring from the shaft holding the roller...cleaned up the shaft and installed new roller with fiber washers. Slid the drum back in place and put shroud and front cover back on. I also replaced a front panel clip that I had broken on a previous repair. It just snapped into place.
Read less
Was this helpful?
Thank you for voting!
noise coming from dryer and low air flow
1 of 4 people found this instruction helpful.
  • Ronald from Aliquippa, PA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Remove front panel, front drum support, remove belt, drum, blower cover, spring clip, blower cover, blower wheel assy.
Ordered new parts on line, came in two days, good service. Cleaned out all lint and installed new parts in reverse order.
Was this helpful?
Thank you for voting!
  • 1

DIY Questions and Expert Answers

Be the first to ask our experts a question about this part!

This Part Also Fits These Models

Don't see your model? Use our Fit Checker to confirm!

Check Part Fit
Part #WP22001650
Brand
Model Number
Description
Maytag
6329
Washer - MAYTAG AUTOMATIC WASHER
Maytag
6349
Washer - MAYTAG AUTOMATIC WASHER
Maytag
6359
Washer - MAYTAG AUTOMATIC WASHER
Amana
7493-LEM437
Dryer - DRYER
Maytag
A104
Washer - Top Loading
Maytag
A105
Washer - Top Loading
Maytag
A106
Washer - Top Loading
Maytag
A106S
Washer - Residential
Maytag
A107
Washer - Top Loading
Maytag
A107S
Washer - Residential
Maytag
A108
Washer - Top Loading
Maytag
A108S
Washer - Residential
Maytag
A110
Washer - Top Loading
Maytag
A112
Washer - Top Loading
Maytag
A15CA
Washer
Maytag
A15CM
Washer
Maytag
A15CT
Washer
Maytag
A16CA
Washer
Maytag
A16CM
Washer
Maytag
A16CT
Washer
Maytag
A17CA
Washer
Maytag
A17CM
Washer
Maytag
A17CT
Washer
Maytag
A180
Washer - Top Loading
Maytag
A181
Washer - Top Loading
Maytag
A182
Washer - Top Loading
Maytag
A183
Washer - Top Loading
Maytag
A18CA
Washer
Maytag
A18CM
Washer
Maytag
A18CT
Washer
Spring Retaining Clip
$15.40
In Stock
✖
Stock Status

In Stock

Item is in stock and is estimated to be delivered in 2-3 business days via Standard Shipping.

On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.