SPRING- CH
$14.16
In Stock
PartSelect Number
PS11738537
Manufacturer Part Number
WP12565502
Manufactured by
Whirlpool
Troubleshooting
This part fixes the following symptoms:
Not dispensing water
This part works with the following products:
Refrigerator.
This part works with the following products:
Maytag, Amana, Whirlpool, Kenmore.
Part# WP12565502 replaces these:
AP6005488, 12565501, 12565502
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Significant frost forming on ice chute.
Following diagram on website, I removed the 2 screws on the face of freezer door ice dispencer.Removed old chute door and solenoid. Replaced with new. I purchased all parts involved because they were inexpensive. The issue was most likely the solenoid.After installation ,the chute door had a sound of being positively closed by the solenoid.I\Frost no longer forming!
Other Parts Used:
-
LORIN from PHILADELPHIA, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
49 of 716 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water / Ice dispenser broken
This repair was really easy. I first removed the water evaporator tray exposing 2 nuts and removed them with driver. Detach the dispenser faceplate and unplug the connections from the circuit board. Remove 2 more nuts holding the dispenser yoke paddle.
Remove the snap in paddle and replace with new part and spring. Complete assembly in reverse order. 10 minutes to complete repair.
Remove the snap in paddle and replace with new part and spring. Complete assembly in reverse order. 10 minutes to complete repair.
Other Parts Used:
-
Paul from Baldwinsville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
24 of 31 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice/Water Dispenser Pedal not working consistently
1. Pull off the removable drip tray that covers the two screws. 2. Remove these octagon shaped screws with the appropriate tool. 3. Remove the cover. ( You can cover a screw driver with a thin cloth so as not to scratch the stainless steel and then slide it between the refrigerator and the cover.) 4. Remove the three connectors from the circuit board. 5. Remove two more nuts holding the dispenser yoke paddle. IMPORTANT: Note how the spring is attached to the paddle.TIP: Take pictures as you remove it and a close up of the spring so as not to forget how it is attached. 6. Snap off the paddle and spring. NOTE: There is another spring attached to the ice dispenser cover. Do not disturb this spring. 7. Replace the paddle and spring making sure the spring is placed correctly in the slot. 8. Complete by reversing the steps above.
Other Parts Used:
-
Charlen from HARRISBURG, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice cube door not shutting
Took the front panel off,replaced the parts inside on the door ,Replaced the panel ,Tested
Now found out that it is the solniod that is bad ,Part on order ,Thanks
Now found out that it is the solniod that is bad ,Part on order ,Thanks
Other Parts Used:
-
Ralph from St Petersburg, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
8 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kirby
October 22, 2017
The water does not shut off completely when dispenser is used. Have to manually return pad to closed position but even then, water continues to come out for 2 seconds or so.
For model number MFI2269VEM10
Hi Kirby,
Thank you for your question. It could possibly be the electrical solenoid that is part of your chute, part number: PS11738676 (Black) or PS11738677 (White). You may also want to check your water inlet valve as well. It could be that part is sending up too much water or not shutting off right away. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11738537
Manufacturer Part Number: WP12565502
Manufacturer Part Number: WP12565502
Brand
Model Number
Description