DISPENSER
Fits your WFL98HEBU0 Washer!
$341.90
In Stock
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your WFL98HEBU0 Washer!
PartSelect Number
PS11731672
Manufacturer Part Number
W10862190
Manufactured by
Whirlpool
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Maytag.
Part# W10862190 replaces these:
W10351801, W10628741, W10817720, W10838697
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 1 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Mouse chewed supply hoses and detergent tray
Took the top off. Identified the parts needed. Ordered the parts. Installed the parts.
Other Parts Used:
-
Natalie from DENVER, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Samuel
December 13, 2019
I have water getting into the soap tank. Its supposed to last 12 loads or so until it needs refilling but it never goes empty because some water is getting into the tank. Eventually it's just water in the soap tank. This doesn't have a soap cup. What might be causing this?
For model number MHW8200FW0
Hello Samuel, thank you for writing. This sounds like the Distribution Nozzle, part number PS11744916, that sits below the upper portion of the Dispenser is missing or broken. You will want to replace it. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
RICH
September 2, 2022
It appears that I am only getting about 4-5 loads of laundry before my yellow "low detergent" light is displayed and my detergent dispenser is close to empty. I have not changed my concentration settings, which are still set at 2x. Do you know what would be causing this issue and what part I would need? (Entire Dispenser assembly, actuator, sensor, flow valve?)
For model number WFW92HEFW0
Hello Rich, thank you for asking! From the description of the problem, it looks like the dispenser actuator switch (part number: PS11753574) is defective. It is the part that triggers the detergent release into the tub. Replacing this part mostly solves the issue. We hope this helps, please feel free to contact customer service for assistance regarding purchase or repair. Thank you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Mark
October 23, 2019
Water is leaking out back side of the dispenser by the plastic clip/clamp that holds the dispenser lid on. Seems to be leaking out between the lid and base of the dispenser. Potentially, just pull out and clean? Or order top and bottom of dispenser?
For model number wfw92hefw0
Hello Mark, thank you for your question. Most likely, the drawer and hoses just need to be cleaned. Alot of time with these units the drawer will get clogged with soap residue and the water can't drain as quickly causing the leak. If there are any cracked or broken pieces when you're cleaning the unit, you will want to replace the corresponding parts. I hope this helps!
Was this helpful?
Thank you for voting!
Sam
December 13, 2019
Water is getting into the soap tank. How do i fix this issue?Thanks
sam
For model number MHW8200FW0
Hello Sam, thank you for your question. There should be water going into the dispenser that holds the soap to rinse the soap into the unit. If there is too much water, or standing water when you open the dispenser after a cycle, the dispenser drawer and cups, and inlet and outlet tubes should be cleaned. If the issue persists, the flow meter might have failed. I hope this helps.
Was this helpful?
Thank you for voting!
Albert
August 27, 2019
Load and go detergent dispenser is not delivering the detergent.
For model number WFW92HEFCO
Hi Albert,
Thank you for your question. If the detergent is not dispensing, it could be that not enough water is flowing through the dispenser. Check to make sure that the flow of water in the dispenser is sufficient enough to flush the detergent out. If it is, check the dispenser actuator switch and the detergent dispenser and see if one of these parts is causing the issue. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11731672
Manufacturer Part Number: W10862190
Manufacturer Part Number: W10862190
Brand
Model Number
Description