This washer lid lock is for laundry centers.
Washer lid lock prevents the washer lid from opening during the wash cycle and spin cycle.
Unplug the laundry center before installing this part. Wear work gloves to protect your hands during the repair.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Crosley.
Part# 137353302 replaces these:
AP5962162
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
David V - September 30, 2020
Verified Purchase
Simple repair
The part was exactly as described and matches the OEM part precisely. The most difficult aspect of the repair was figuring out how to take off the front panel of the washer.
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tom
January 9, 2019
Everything works starts washes drains just won't spin
For model number FFLE3911QW0
Hello Tom, Thank you for the question. I suggest testing or replacing the PartSelect Number PS11703540 Washer Lid Lock. If the lock is defective it can not tell if the lid is closed and ok to start the spin cycle. For safety reasons the appliance will not spin of the lid is open. Hope this helps, good luck with this repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
February 23, 2018
My Frigidaire washer dryer combo won't fill with water. I've changed the water inlet valve it still won't fill?
For model number FFLE4033QW
Hi Steve, Thank you for the question. You will need to check to see if there is power going to the valve. If there is no power to the valve you may need to replace the control board, PartSelect Number PS11703854. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Lori
May 7, 2018
Lid locks and will fill and aggitate but wont drain and spin unless i move the dial to spin cycle
For model number FFLG3911QW0
Hi Lori,
Thank you for your question. If the dial is not advancing, there are some parts that you will need to check to see which ones are causing the issue. You will need to check the lid switch, the timer, the timer knob, the drain pump and the water inlet valve. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Amir
November 4, 2019
Hi, Our washer/dryer does everything well, but when it should start spinning, it moves very slow for few seconds and then stops like the job has been finished. Can you advise which part can cause this issue?
Is there any service manual I can use for troubleshooting? Thanks
For model number 41761722510
Hi Amir,
Thank you for your question. If the washer is not spinning correctly, I suggest the lid lock. If the lock is defective it can prevent the washer from not working correctly. The belt should be checked as well. If your washer does not spin you should inspect the drive belt for signs of overheating or excessive wear. Before replacing a damaged belt, you should verify that any belt tensioning device such as an idler pulley or motor glide is operating properly and moves freely. You should also check the electronic control board and the motor to make sure that they are operating correctly. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Kenneth
October 26, 2022
Hi my Washer Combo works in all cycles .It will wash ,rinse and spin but does not go into done cycle. I cannot open the washer door .It wont release I move the dial to cycle and the washer stops .
For model number CFLE3900UW2
Hi Kenneth, thank you for reaching out. According to our research on the model, the Lid Lock appears to be faulty and you may need to replace it with part number PS11703540. If you need help placing an order, customer service is available 7 days a week. Glad to be of help!
Was this helpful?
Thank you for voting!
Jim
January 28, 2023
Washer stops middle of random cycles. 3 beeps, 3 beeps. Could not find that code. Any ideas?
For model number fflg3911qw1
Hello Jim, thank you for your question. The lid lock is likely the issue. However, we attached a video for you to view on diagnosing as well. Thank you and have a great day.
Was this helpful?
Thank you for voting!
ALLAN
April 19, 2023
CAN I GET THE CASING WITH OUT THE SWITCH
For model number FFLE39CIQW0
Hi Allan, thank you for reaching out. Sadly, the casing is not sold individually, you may need to buy the whole lid lock assembly, part number PS11703540. We hope this information is useful!
Was this helpful?
Thank you for voting!
Tad
December 6, 2023
just bought this washer/dryer combo...the lid lock is broken, the washer will not start, is it bc the lid lock is broken?
For model number ffle3911qwo
Hello Tad, thank you for asking. According to our research, if the lid lock is broken, then you may need to replace the lid lock, part number PS11703540, to fix the issue. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
