Models > YWFE510S0HW0 > Instructions

YWFE510S0HW0 Whirlpool - Instructions

All Instructions for the YWFE510S0HW0
31 - 45 of 154
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Switch worked off and on but you could not set heat to a specified temperature.
Remove back panel 10 screws. Disconnect plug in fixture from switch. Front of range remove knob (it just pulls out) remove 2 screws, remove switch. To install reverse procedure.
Parts Used:
Dual Element Control Switch
  • Dale from POUND, WI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad element replacement
Took off top and pulled out old element and plugged in the new one
Parts Used:
6" Surface Element, 1200 W
  • Thomas from Warren, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
9 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F1 E0 CODE.
UNPLUG RANGE. PULL OUT AND REMOVE TOP REAR SHEET METAL COVER. UNPLUG CONTROL UNIT, AND REMOVE AS AN ASSEMBLY. INSTALL NEW ELECTRICAL CONTROL BOARD / DISPLAY UNIT WITH NEW P/N: W11567348. REINSTALL SHEET METAL COVER, PLUG IN. TEST. OPS CHECK GOOD.
Parts Used:
CNTRL-ELEC
  • Christoph from PORT ST LUCIE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element wasn't being controlled by the switch it would stay on high
Ordered a new switch and replaced the old one with it.
Parts Used:
Surface Burner Element Switch, Large Burner
  • George from FRANKLIN, KY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Parts Used:
Light Bulb - 40W
  • Carl from RIVERSIDE, CA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers
7 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I broke a piece of the trim and had to replace it
took the handle off, replaces the side trim piece and replaced the handle. Very simple!
Parts Used:
Side Trim - Right Hand Side
  • Gregg from SOUTH BEND, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both right and left side trims were broken.
Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.
Parts Used:
Side Trim - Left Side - White Side Trim - Right Hand Side
  • A D from HOUSTON, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2nd 8 inch burner switch in a little over a year to not always hold selected tempurature.
As a former appliance repairman, the installation went just like the repair instruction video.
Just use care not to scratch anything and clean behind the appliance and cabinet walls, etc. It's worth a hug and a piece of pie!
Parts Used:
Surface Burner Element Switch, Large Burner
  • LELAND from HERMISTON, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Parts Used:
Main Power Terminal Block
  • Dana from Black Mountain, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner Element did not work
Shut off breaker. Remove a total of 3 screws attach wires, replace screws, turn breaker on. Done!
Parts Used:
ELMNT-SURF
  • Paul from Reedsburg, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top burner would not turn off at any time.
Unpluged range for safety (power earlier removed by circuit breaker turnoff).
Removed two screws from front switch cover.
Removed knob from effected switch and removed the wires on the back of the switch.
Removed two screws holding switch and removed switch.
Reversed the process to install new switch.
The entire project took about ten minutes.
Parts Used:
Surface Burner Element Switch, Large Burner
  • Donald from Byron, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler element not working
It went great. I am not very handy, but with a little help from your website reviews, I was able to easily remove the old broiler element and replace it with the new one in less than an hour. I immediately tested it and found that it worked great.
Parts Used:
Broil Element
  • Normand from Lincoln, RI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
6 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wasn't preheating to temperature
Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).
Parts Used:
Oven Sensor
  • Margaret from WALDORF, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bard burner switch
Removed rear panel disconnect power from wall removed old switch and replaced with new switch and reassembled
Parts Used:
Dual Element Control Switch
  • Edward from KISSIMMEE, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven sensor was not regulating heat set for oven
Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too
Parts Used:
Oven Sensor
  • Linda from SAINT CLOUD, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YWFE510S0HW0
31 - 45 of 154
Back to Top