YWED6400SW1 Whirlpool Dryer - Instructions

took off about 8 screws, opened door into it's front & back parts, popped out the old/broken door catches and re-inserted replacements. Only 1 is needed, but this is the 2nd one to break. The first time a repairman switch the un-used from right side to left. (there are 2 so the door can be hung left or right opening)

Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!

First unplug the dryer.
Remove the lint filter.
Remove two(2) screws by the filter.
Use a screwdriver to raise the top of the dryer.
Unplug wires going to the front panel (pull apart)
Remove two(2) hex head screws.
Lift front panel out of the way.
Use a light to view the pulley assembly on the bottom.
Raise the pulley to remove the drive belt.
Use a hex socket to remove one(1) bolt from the bracket.
Install new part.
Reverse order of dis-assembly.
Very Very Easy!

The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about two days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.

I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint screen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.

the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.

Just like video except there were two screws in back to take control head off. Be prepared to have shop vacation ready. Clean dryer duct too. Have bandaids ready. Plastic triangles are not easy to take off, video makes it look easy.

Very bad design to keep door shut but very simple to fix. Just screw bad strike out and screw new one end. Whirlpool should have gave extra when you buy this type dryer.

1. Shut off gas and disconnected dryer.
2. Opened cabinet. Easy sheet metal screws and fairly obvious how everything goes together. NB: You'll need a block (or a helper to hold things while you run to look for one) to hold the drum while removing the front.
3. The motor is connected with a single harness, so wiring is a snap.
4. Removing the blower wheel from the back was hard. I braced the motor shaft and turned with all the leverage I could muster, but it was stuck. Plan B: Recip saw to cut the shaft. Motor comes out one side and the fan comes out the other.
5. The fan, of course, was unusable because there was still a piece of motor shaft stuck in the thread. This is why I had to spring for a new wheel.
6. Put everything back together and receive wife's adoring praise...

Like another reviewer's repair story, I decided to take the door apart. It was too difficult, at least for me, to get the faulty catch out without damaging either the the door or my hands. This is why I give it an "easy" rather than "very easy" rating and put the total repair time at a half hour or better. I also decided I wanted a second person to help - not with getting the door apart or putting it back together, but because a second pair arms was very helpful in rehanging the door well. We removed the door (four screws), marking which side of the hinge needed to be flush with the actual dryer when rehanging. Then we took the door apart, which comprises another sixteen screws (four on each edge). We used an electric drill but I'm sure it could be done manually. We used needle nosed pliers to get the faulty latch out of that side of the door, then replaced it with the "back up" from the other side. Then we put the door back together and carefully rehung it. Done. We did decide that, in future, all kids (we have three boys) slamming the door would be severely beaten. Pushing the door until it's against the dryer, then PUSHING (as opposed to slamming) the latch ONTO the catch pin on the dryer is obviously what was intended. However, I've learned not to count on my boys being particularly conscientious, so I'd ordered four replacement latches to keep on hand. This machine was delivered in April 2009 and I replaced the latch in April 2011. Based on this and our laundering habits, I'm sure the others will be used long before the dryer calls it quits.

Removed the broken catch with a pair of needle nose pliars and replaced it the same way. Took about 10 minutes. Saved a Service Call

I ordered the dryer repair kit and to my surprise it arrived 4 days early. I followed the video instructions on the parts select website to replace 4 rollers, belt and belt pulley. A 1/4 in nut driver attached to my Dewalt drill made life ALOT easier!! My recommendation, when you remove the rollers, take a rag and really clean up the shaft they ride on. Then apply a lightweight spray oil to the shafts. When you install the new rollers they will spin free and easy. Having the dryer apart is also a great time to break out the dust buster of vacuum. Spin the fan motor up front by hand and use vacuum to remove lint or belt shaving from inside the cabinet. Add this step as good fire prevention measure.

Unplug dryer from receptial. Poped top off, useing thin bladed screw driver to push tintion springs, while pulling up on lid. removed two no 10 sheet metal screws, useing 1/4 nut driver, this removes loading door by pulling uo 1/4 inch. Removed twi NO 10 sheet metal screws useing 1/4 nut driver, removed front carrage system. Removed belt then tub. Removed idler arm spring useing plires, used 5/8 inch socket removed sholder bolt with arm. Reverced procedure with one execption. Used two by four to hold tub up so belt could be put on, rolled tub to alline belt. Not bad for 70 Years young. Curtiss

We watched the video at whirlpool.com! Made it so simple anyone could have done it!

BEFORE ANYTHING ELSE UNPLUG THE POWER AND TURN OFF THE GAS SUPPLY 1. unscrew the 3 nut screws at the back to remove the cover lid. 2. pull the control console cable from the electronic board. (only 3 wires on it).3. unscrew the 2 nut screws of the control console then remove it by pulling up.4. unscrew the 5 screws to remove the door. (pull little up to unhinged then remove). 6. unscrew the 5 nut screws to remove the lower siding. 7. unscrew the copper 4 nut screws then remove the lint suction fixture 8. unscrew the 4 nut screws to remove door fixture ,then just lay next to the machine.(the wires are long enough so you don't need to unplug and separate it from the machine.9. remove the belt by pulling the idler pulley towards the motor pulley (against the tension spring) 10. remove the drum by lifting a little bit upward. 11. remove the plastic triangular lock using a small screw driver then remove the idler pulley wheel then install the replacement. (clean your machine using a vacuum cleaner and remove all the lints). 12. install back the drum, be sure to set the drum belt to the right position. (groove on drum side). 13. install back the belt to the pulley the same procedure as to remove it. 14. assemble back what you have removed. end.